Stress Distribution in Wear Analysis of Nano-Y2O3 Dispersion Strengthened Ni-Based μm-WC Composite Material Laser Coating
Open Access
Abstract
Oxide-dispersion- and hard-particle-strengthened (ODS) laser-cladded single-layer multi-tracks with a Ni-based alloy composition with 20 wt.% μm-WC particles and 1.2 wt.% nano-Y2O3 addition were produced on ultra-high-strength steel in this study. The investigation of the composite coating designed in this study focused on the reciprocating friction and wear workpiece surface under heavy load conditions. The coating specimens were divided into four groups: (i) Ni-based alloy, nano-Y2O3, and 2 μm-WC (2 μm WC-Y/Ni); (ii) Ni-based alloy with added 2 μm-WC (2 μmWC/Ni); (iii) Ni-based alloy with added 80 μm-WC (80 μmWC/Ni); and (iv) base metal ultra-high-strength alloy steel 30CrMnSiNi2A. Four conclusions were reached: (1) Nano-Y2O3 could effectively inhibit the dissolution of 2 μm-WC. (2) It can be seen from the semi-space dimensionless simulation results that the von Mises stress distribution of the metal laser composite coating prepared with a 2 μm-WC particle additive was very uniform and it had better resistance to normal impact and tangential loads than the laser coating prepared with the 80 μm-WC particle additive. (3) The inherent WC initial crack and dense stress concentration in the 80 μm-WC laser coating could easily cause dislocations to accumulate, as shown both quantitatively and qualitatively, resulting in the formation of micro-crack nucleation. After the end of the running-in phase, the COF of the 2 μm-WC-Y2O3/Ni component samples stabilized at the minimum of the COF of the four samples. The numerical order of the four COF curves was stable from small to large as follows: 2 μm-WC-Y2O3/Ni, 2 μm-WC/Ni, 80 μm-WC/Ni, and 30CrMnSiNi2A. (4) The frictional volume loss rate of 2 μm-WC-Y2O3/Ni was 1.3, which was significantly lower than the corresponding values of the other three components: 2.4, 3.5, and 13.Keywords
Funding Information
- National Natural Science Foundation of China (51075328, 51675424, 3102015BJ (II) MYZ28)
- Fundamental Research Funds for the Central Universities (51075328, 51675424, 3102015BJ (II) MYZ28)
This publication has 34 references indexed in Scilit:
- Effect of Ultra-fine WC Particles on Microstructural Evolution and Wear Behavior of Ni-Based Nano-CeO2 Coatings Produced by LaserRare Metal Materials and Engineering, 2018
- Microstructure and Wear Resistance of Laser Cladded Ni-based Coatings with Nanometer La 2 O 3 AdditionRare Metal Materials and Engineering, 2017
- Effect of rare earth elements and their oxides on tribo-mechanical performance of laser claddings: A reviewJournal of Rare Earths, 2016
- Corrosion and wear behavior of laser cladded Ni–WC coatingsSurface and Coatings Technology, 2015
- Laser cladding assisted by induction heating of Ni–WC composite enhanced by nano-WC and La2O3Ceramics International, 2014
- Preparation and characterization of sintered molybdenum doped with MoSi2/La2O3/Y2O3 composite particleMaterials Science and Engineering: A, 2012
- Effects of CeO2 nanoparticles on microstructure and properties of laser cladded NiCoCrAlY coatingsJournal of Rare Earths, 2010
- Degradation of space exposed surfaces by hypervelocity dust bombardment, and refractory materials for spaceInternational Journal of Refractory Metals and Hard Materials, 2009
- Noise in Sliding Friction under Wear Conditions: The Role of DebrisPhysical Review Letters, 2009
- Abrasive wear resistance of aluminium alloy/ceramic particulate compositesWear, 1996