Intermediate Phase Suppression with Long Chain Diammonium Alkane for High Performance Wide‐Bandgap and Tandem Perovskite Solar Cells
Authors:
- 17 March 2024
- journal article
- research article
- Published by Wiley in Advanced Materials
- Vol. 36 (25) , e2400105
Abstract
Wide bandgap (WBG) perovskite can construct tandem cells with narrow bandgap solar cells by adjusting the band gap to overcome the Shockley−Queisser limitation of single junction perovskite solar cells (PSCs). However, WBG perovskites still suffer from severe nonradiative carrier recombination and large open‐circuit voltage loss. Here, this work uses an in situ photoluminescence (PL) measurement to monitor the intermediate phase evolution and crystallization process via blade coating. This work reports a strategy to fabricate efficient and stable WBG perovskite solar cells through doping a long carbon chain molecule octane‐1,8‐diamine dihydroiodide (ODADI). It is found that ODADI doping not only suppresses intermediate phases but also promote the crystallization of perovskite and passivate defects in blade coated 1.67 eV WBG FA0.7Cs0.25MA0.05Pb(I0.8Br0.2)3 perovskite films. As a result, the champion single junction inverted PSCs deliver the efficiencies of 22.06% and 19.63% for the active area of 0.07 and 1.02 cm2, respectively, which are the highest power conversion efficiencies (PCEs) in WBG PSCs by blade coating. The unencapsulated device demonstrates excellent stability in air, which maintains its initial efficiency at the maximum power points under constant AM 1.5G illumination in open air for nearly 500 h. The resulting semitransparent WBG device delivers a high PCE of 20.06%, and the 4‐terminal all‐perovskite tandem device delivers a PCE of 28.35%.Keywords
Funding Information
- National Natural Science Foundation of China (12134010, 62074117, 61904126, 12174290)
- Natural Science Foundation of Hubei Province (2023BAB102, 2021CFB039)
- National High-tech Research and Development Program (2015AA050601)
This publication has 55 references indexed in Scilit:
- Low‐Dimensional 2‐thiopheneethylammonium Lead Halide Capping Layer Enables Efficient Single‐Junction Methylamine‐Free Wide‐Bandgap and Tandem Perovskite Solar CellsAdvanced Functional Materials, 2023
- Stabilizing Perovskite Precursor by Synergy of Functional Groups for NiOx‐Based Inverted Solar Cells with 23.5 % EfficiencyAngewandte Chemie International Edition, 2022
- Quasi‐2D Bilayer Surface Passivation for High Efficiency Narrow Bandgap Perovskite Solar CellsAngewandte Chemie International Edition, 2022
- Gas‐Assisted Spray Coating of Perovskite Solar Cells Incorporating Sprayed Self‐Assembled MonolayersAdvanced Science, 2022
- Unlocking Voltage Potentials of Mixed‐Halide Perovskite Solar Cells via Phase Segregation SuppressionAdvanced Functional Materials, 2021
- Wide Bandgap Interface Layer Induced Stabilized Perovskite/Silicon Tandem Solar Cells with Stability over Ten Thousand HoursAdvanced Energy Materials, 2021
- Large‐Area Blade‐Coated Solar Cells: Advances and PerspectivesAdvanced Energy Materials, 2021
- High Performance of Planar Perovskite Solar Cells Produced from PbI2(DMSO) and PbI2(NMP) Complexes by Intramolecular ExchangeAdvanced Materials Interfaces, 2016
- Toward Large Scale Roll‐to‐Roll Production of Fully Printed Perovskite Solar CellsAdvanced Materials, 2015
- Enhanced Environmental Stability of Planar Heterojunction Perovskite Solar Cells Based on Blade‐CoatingAdvanced Energy Materials, 2014