A Simple Solid-State Direct Bonding Process for Fabrication of Ohmic Contacts on n-type Mg3Sb2-xBix-based Thermoelectric Materials
Authors:
- Sung-Jae JooSJSung-Jae Joo
- Kim KimKKKim Kim
Open Access
- 5 January 2025
- journal article
- research article
- Published by The Korean Institute of Metals and Materials in Korean Journal of Metals and Materials
- Vol. 63 (1) , 60-67
Abstract
N-type Mg3Sb2-xBix materials are expected to replace n-type bismuth telluride because they are more abundant in the Earth's crust and lower in cost. However, the metallization process of this material, which is essential to develop modules, has been relatively under-researched. According to the literature, one-step sintering process based on powder metallurgy is mostly used to form an ohmic bonding layer on n-type Mg3Sb2-xBix materials. However, this method is not reproducible nor practical, and is unsuitable for industrial mass production. This paper presents a new, simple method for metallization, the solid-state direct bonding of Mg and Cu foils on sintered n-type Mg3Sb2-xBix. It employs interdiffusion between the thermoelectric material and the metal layer at elevated temperatures to form a tight and robust bond. Mgwas chosen as the contact metal so that the interdiffusion of Mg would not cause a Mg deficiency in the Mg3Sb2-xBix near the interface. Then, a Cu layer was selected as the second metal to wrap around the Mg layer so that the subsequent soldering process could be the same as that of bismuth telluride. Solid-state bonding with the Mg/Cu double layer formed a structurally perfect joint at 723 K. When the temperature of the solid-state bonding exceeded 750 K, the eutectic point of Mg and Cu, the Mg layer was lost due to liquid phase formation. Solid-phase bonding at 723 K produced no noticeable change in the Seebeck coefficient near the interface, which would be caused by the outdiffusion of Mg from the n-Mg3Sb2-xBix. The specific contact resistance was about 53.8 μΩ cm2. This is superior to the values reported for n-type Bi2Te3-based materials. In this study, we also fabricated a Mg3Sb2-xBix (n)-Bi2Te3 (p) hybrid thermoelectric module and evaluated the output characteristics, which confirmed the high applicability of our solid-state bonding process.Keywords
Funding Information
- Ministry of Science and ICT
- National Research Council of Science and Technology (24A01025)
This publication has 21 references indexed in Scilit:
- Thermoelectric Generators: A comprehensive review of characteristics and applicationsApplied Thermal Engineering, 2022
- Se-induced enhancement of the high-temperature thermoelectric performance of n-type Cu0.008Bi2(Te,Se)3 alloys due to suppressed bipolar conductionJournal of Alloys and Compounds, 2021
- Compromise between band structure and phonon scattering in efficient n-Mg3Sb2-Bi thermoelectricsMaterials Today Physics, 2021
- Scalable synthesis of n-type Mg3Sb2-xBix for thermoelectric applicationsMaterials Today Physics, 2021
- Reliable N-type Mg3.2Sb1.5Bi0.49Te0.01/304 stainless steel junction for thermoelectric applicationsActa Materialia, 2020
- Effect of group-3 elements doping on promotion of in-plane Seebeck coefficient of n-type Mg3Sb2Journal of Materiomics, 2020
- Prospects of waste-heat recovery from a real industry using thermoelectric generators: Economic and power output analysisEnergy Conversion and Management, 2020
- Realizing high conversion efficiency of Mg3Sb2-based thermoelectric materialsJournal of Power Sources, 2019
- Extraordinary thermoelectric performance in n-type manganese doped Mg3Sb2 Zintl: High band degeneracy, tuned carrier scattering mechanism and hierarchical microstructureNano Energy, 2018
- Isotropic Conduction Network and Defect Chemistry in Mg3+δSb2‐Based Layered Zintl Compounds with High Thermoelectric PerformanceAdvanced Materials, 2016