Conjugated Polymers Based on Benzo[2,1-b:3,4-b′]dithiophene with Low-Lying Highest Occupied Molecular Orbital Energy Levels for Organic Photovoltaics
- 16 June 2009
- journal article
- research article
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 1 (7) , 1613-1621
Abstract
Fusing bithiophene units with a benzo moiety, benzo[2,1-b:3,4-b′]dithiophene (BDT), was projected by theoretical calculations to lower the highest occupied molecular orbital (HOMO) energy level of the resulting polymers compared with that of the bithiophene unit, which would enhance the open circuit voltage of bulk heterojunction photovoltaic cells fabricated from BDT-based polymers blended with PCBM. The homopolymer of BDT (HMPBDT) and alternating copolymer of BDT with 2,1,3-benzothiadiazole (PBDT-BT) were therefore synthesized and fully characterized. Both the homopolymer (HMPBDT) and the copolymer (PBDT-BT) were experimentally confirmed to have low HOMO energy levels (−5.70 eV for HMPBDT and −5.34 eV for PBDT-BT). Introducing the acceptor moiety (2,1,3-benzothiadiazole) successfully lowered the optical band gap of the copolymer from 2.31 eV (HMPBDT) to 1.78 eV (PBDT-BT). Bulk heterojunction photovoltaic devices were fabricated from blends of these structurally related polymers with PBCM to investigate the photovoltaic performances. The optimized device of HMPBDT:PCBM (1:3, 180 nm) exhibited an improved open circuit voltage (Voc) of 0.76 V, a short circuit current (Jsc) of 0.34 mA/cm2, and a fill factor (FF) of 0.40, offering an overall efficiency of 0.10%. The observed large phase separation of the thin film by AFM and the large band gap were accountable for the small current. The optimized device of PBDT-BT:PCBM (1:3, 55 nm) demonstrated a better efficiency of 0.6%, with Voc = 0.72 V, Jsc = 2.06 mA/cm2, and FF = 0.42. The much improved current was attributed to the lower bandgap and better film morphology. However, the low hole mobility limited the thickness of the PBDT-BT:PCBM film, making inaccessible the thicker film which would utilize more light and enhance the current. Further improvements are expected if the mobility and film morphology can be improved by the new materials design, together with low band gap and low HOMO energy level.Keywords
This publication has 36 references indexed in Scilit:
- A New Donor–Acceptor–Donor Polyfluorene Copolymer with Balanced Electron and Hole MobilityAdvanced Functional Materials, 2007
- Stoichiometry, mobility, and performance in bulk heterojunction solar cellsApplied Physics Letters, 2007
- Efficient Tandem Polymer Solar Cells Fabricated by All-Solution ProcessingScience, 2007
- Low band gap polymers for organic photovoltaicsSolar Energy Materials and Solar Cells, 2007
- Determining the internal quantum efficiency of highly efficient polymer solar cells through optical modelingApplied Physics Letters, 2007
- High Photovoltaic Performance of a Low‐Bandgap PolymerAdvanced Materials, 2006
- Influence of Solvent Mixing on the Morphology and Performance of Solar Cells Based on Polyfluorene Copolymer/Fullerene BlendsAdvanced Functional Materials, 2006
- A strong regioregularity effect in self-organizing conjugated polymer films and high-efficiency polythiophene:fullerene solar cellsNature Materials, 2006
- High-efficiency solution processable polymer photovoltaic cells by self-organization of polymer blendsNature Materials, 2005
- Thermally Stable, Efficient Polymer Solar Cells with Nanoscale Control of the Interpenetrating Network MorphologyAdvanced Functional Materials, 2005