СТРУКТУРНО-ФАЗОВЫЕ СОСТОЯНИЯ ПЛАЗМЕННОЙ БЫСТРОРЕЖУЩЕЙ НАПЛАВКИ ПОСЛЕ ОТПУСКА И ЭЛЕКТРОННО-ПУЧКОВОЙ ОБРАБОТКИ
Open Access
- 30 June 2025
- journal article
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 22 (2) , 221-231
Abstract
Методами сканирующей и просвечивающей электронной микроскопии проанализированы структурно-фазовые состояния и дефектная субструктура плазменной наплавки нетоковедущей порошковой проволокой в среде азота быстрорежущей стали Р2М9 на подложку из среднеуглеродистой стали 30ХГСА в исходном состоянии, после высокотемпературного отпуска и электронно-пучковой обработки.Электронно-пучковую обработку проводили при следующих параметрах: энергия ускоренных электронов 18 кэВ, плот-ность энергии пучка электронов 30 Дж/см2, длительность импульса 50 мкс,частота следования 50 Гц, коли-чество импульсов 5. Сформированный наплавленный слой толщиной ~ 5 мм имеет карбидную структуру каркасного типа, которая не разрушается при последующих отпуске и облучении импульсными электрон-ными пучками. В исходном состоянии после наплавки и после отпуска присутствуют карбиды состава MC, M6C, M23C6и M7C3. После электронно-пучковой обработки основным карбидом, формирующим каркас, яв-ляется карбид состава M6C. Плазменная наплавка сопровождается формированием мартенситной структу-ры, по границам и в объеме кристаллов мартенсита выявлены наноразмерные включения второй фазы, име-ющие следующий состав: MoC, Mo2C, M6C. Их относительное содержание составляет 34 масс. %. в исход-ном состоянии, 33 масс. % после отпуска и 19 масс. % послеэлектронно-пучковой обработки. The structural-phase states and defect substructure of plasma surfacing with non-current flux-cored wire in the nitrogen medium of R2M9 high-speed steel on the substrate of medium-carbon steel 30HGSA in the ini-tial state, after high-temperature tempering and electron beam treatment were analyzed using scanning and transmis-sion electron microscopy. Electron beam processing was carried out with the following parameters: the energy of accelerated electrons is 18 keV, the energy density of the electron beam is 30 J/cm2, the pulse duration is 50 micro-seconds, the repetition frequency is 0.3 Hz, the number of pulses is 5.The formed deposited layer with a thickness of ~5 mm has a frame-type carbide structure, which is not fractured during subsequent tempering and pulsed elec-tron beams irradiation. Carbides in compositions MC, M6C, M23C6and M7C3are present in the initial state after sur-facing and after tempering. After electron beam treatment, the main carbide forming the frame is M6C carbide. Plasma surfacing is accompanied by the formation of martensitic structure; nanosized inclusions of the second phase, having the following compositions: MoC, Mo2C, M6C, were identified along the boundaries and in the vol-ume of martensite crystals. Their relative content is 34 wt. %. in the initial state, 33 wt. % after tempering and 19 wt. % after electron beam treatment.Keywords
This publication has 8 references indexed in Scilit:
- Structure and Properties of R18U Surfacing of Highspeed Steel After its High TemperingRussian Physics Journal, 2023
- STRUCTURE AND PROPERTIES OF PLASMA COATINGS FROM HIGH-SPEED STEEL AFTER HIGH-TEMPERATURE TEMPERINGBulletin of the Siberian State Industrial University, 2023
- Complex fine-scale diffusion coating formed at low temperature on high-speed steel substrateApplied Surface Science, 2018
- Electron-beam modification of a surface layer deposited on low-carbon steel by means of arc sprayingBulletin of the Russian Academy of Sciences: Physics, 2017
- Design of AlCrSiN multilayers and nanocomposite coating for HSS cutting toolsApplied Surface Science, 2015
- The effects of AlCrN coating, surface modification and their combination on the tribological properties of high speed steel under dry conditionsTribology International, 2015
- Investigation of Ti and Cr based PVD coatings deposited onto HSS Co 5 twist drillsApplied Surface Science, 2013
- The influence of metallic interlayers on the adhesion of PVD TiN coatings on high-speed steelWear, 2008