Paleostress magnitudes determination by using fault slip and fluid inclusions planes data
Authors:
- M. LespinasseMLM. Lespinasse
- M. CathelineauMCM. Cathelineau
- 10 March 1995
- journal article
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research
- Vol. 100 (B3) , 3895-3904
Abstract
Paleostress magnitudes can be estimated by using fault slip data, rupture and friction laws (Angelier, 1989) for dry conditions. However, their estimation is difficult if fluids are present during deformation, the lithostatic load and the fluid pressure being generally unknown. This paper shows that the quantitative estimation of the lithostatic load and the fluid pressure during a tectonic event can be derived from paleofluid analysis in fluid inclusion planes, (FIP). As FIP are healed mode I cracks oriented in a consistant manner relative to regional or local structures, stress and fluid features may be obtained for a given deformation event. This approach has been applied to a fault system affecting an Hercynian granite of the NW French Massif Central. A NW‐SE compression has been defined from a population of 51 faults characterized by orientations around N60°E to N110°E for dextral strike slips and N135°E to N175°E for sinistral movements. The stress ratio has been determined with fault slip data around 0.52±0.08 and by using Angelier's method, the ratio ψ (σ3/σ1) was estimated around 0.27±0.03, and the friction coefficient μ was estimated around 0.58±0.1. FIP orientation were measured in a sample collected at 1 meter from the fault. The dominant trend is NW‐SE, vertical or dipping toward the SW. Inclusion fluids from FIP are characterized by homogenization temperatures in the 260°–380°C range with a mode around 300°C and melting temperatures from 0°C to −1.5°C (0–5% equivalent NaCl) with a mode around −1.0°C (1.7% equivalent NaCl). These data yield, assuming a geothermal gradient in the 60°–80°C/km range, and hydrostatic conditions, a fluid pressure estimate of about 50±10 MPa and a σv around 132±10 MPa. Thus a major stress ratio σ1‐σ3 can be estimated in the 70–105 MPa range.Keywords
This publication has 39 references indexed in Scilit:
- Critical stress difference, fault orientation and slip direction in anisotropic rocks under non-Andersonian stress systemsJournal of Structural Geology, 1992
- Palaeoseismic events recorded in Archaean gold-quartz vein networks, Val d'Or, Abitibi, Quebec, CanadaJournal of Structural Geology, 1992
- Microfractures and their role in deformation of a quartz arenite from the central Appalachian forelandJournal of Structural Geology, 1990
- Paleostress directions from the preferred orientation of closed microfractures (fluid-inclusion planes) in sandstone, East Texas basin, U.S.A.Journal of Structural Geology, 1989
- From orientation to magnitudes in paleostress determinations using fault slip dataJournal of Structural Geology, 1989
- High-angle reverse faulting in northern New Brunswick, Canada, and its implications for fluid pressure levelsJournal of Structural Geology, 1989
- Healed microcrack orientations in granite from Illinois borehole UPH-3 and their relationship to the rock's stress historyTectonophysics, 1987
- Criteria for the sense of movement on fault surfaces in brittle rocksJournal of Structural Geology, 1987
- Microfracturing and regional stress field: a study of the preferred orientations of fluid-inclusion planes in a granite from the Massif Central, FranceJournal of Structural Geology, 1986
- An inverse problem in microtectonics for the determination of stress tensors from fault striation analysisJournal of Structural Geology, 1981