Short Communication: The Effect of Water Temperature on the Viability of Silage Inoculants
Authors:
Open Access
- 1 January 2008
- journal article
- Published by American Dairy Science Association in Journal of Dairy Science
- Vol. 91 (1) , 236-240
Abstract
The objective of this study was to determine if exposure to high temperatures in water affects the viability of various silage inoculants. Inoculants were enumerated on De Man, Rogosa, Sharpe agar to standardize a final count (colony-forming units) in water such that about 500 mL added to 1 tonne of wet forage would achieve a recommended application rate of about 100,000 cfu of lactic acid bacteria (LAB) per gram of wet forage. Testing was done in 4 sequences (SEQ). For each SEQ, inoculants were mixed in deionized water for 45 min at 30 degrees C followed by incubation for 6 h at 30 degrees C (SEQ 1), 35 degrees C (SEQ 2), 40 degrees C (SEQ 3), or 45 degrees C (SEQ 4) in duplicate 125-mL flasks rotating at 125 rpm. After 6 h, rotation was stopped and the temperature was lowered to 30 degrees C for the next 18 h for all SEQ. Numbers of LAB were enumerated at 0, 3, 6, and 24 h. Each sequence was repeated twice. Incubation at a moderate temperature (SEQ 1) did not affect the viability of the microbial inoculants. The viability of the inoculants declined with increasing temperature (SEQ 2 to 4) but the effect varied by inoculant. For some inoculants exposure to 35 degrees C resulted in substantial decreases in viable cells (loss of 0.5 to 1 log cfu/mL). Incubation at higher temperatures resulted in even greater losses in viability for some inoculants. Losses of more than 0.5 log cfu/mL would most likely make the application of these inoculants ineffective in the field. Lactobacillus plantarum MTD/1 was the most thermotolerant organism tested, because it was unaffected by all temperatures (30 to 45 degrees C) after 3 h of incubation. Lactobacillus plantarum MTD/1 and Lactobacillus buchneri 40788 also appeared to have better thermotolerance as their numbers substantially increased between 6 and 24 h in SEQ 4. These data show that some silage inoculants are more thermotolerant than others and that precautions should be taken to ensure that microbial inoculants that are applied to forage do not reach elevated temperatures during use.Keywords
This publication has 17 references indexed in Scilit:
- Influence of Ensiling Temperature, Simulated Rainfall, and Delayed Sealing on Fermentation Characteristics and Aerobic Stability of Corn SilageJournal of Dairy Science, 2006
- Thermal inactivation of water-borne pathogenic and indicator bacteria at sub-boiling temperaturesWater Research, 2006
- Heat Shock Response in Lactobacillus plantarumApplied and Environmental Microbiology, 2004
- Silage Additives2003
- Microbiology of Ensiling2003
- Postharvest Factors Affecting Ensiling2003
- The effect of temperature and Lactobacillus amylovorus and Lact. plantarum, applied at ensiling, on wheat silageJournal of Applied Microbiology, 1998
- Identification of sites of injury in Lactobacillus bulgaricus during heat stressJournal of Applied Microbiology, 1997
- Effect of a microbial inoculant (Ecosyl™ and/or a glycopeptide antibiotic (vancomycin) on fermentation and aerobic stability of wilted alfalfa silageAnimal Feed Science and Technology, 1991
- An evaluation through lactating cattle of a bacterial inoculant as an additive for grass silageGrass and Forage Science, 1989