Retention of zirconia crowns to Ti-base abutments: effect of luting protocol, abutment treatment and autoclave sterilization.
Authors:
- 1 January 2021
- journal article
- research article
- Published by Japan Prosthodontic Society in Journal of Prosthodontic Research
- Vol. 65 (2) , 171-175
Abstract
Purpose: To evaluate the influence of resin cement type, surface pretreatment and autoclave sterilization on the retention of Y-TZP crowns to Ti-base abutments. Methods: Y-TZP crowns were designed and milled to fit Ti-base abutments. Crowns were cemented using either a conventional resin cement (conventional) with a universal adhesive or a self-adhesive resin cement (self-adhesive), both following no surface pretreatment (No) or Ti-base abutment sandblasting (SB) (n=20/group). Half of the cemented samples were subjected to in-office autoclave sterilization. Pullout testing was performed in a universal testing machine at a speed of 1 mm/min until crown displacement. Data were statistically evaluated through a linear mixed model following post hoc comparisons by LSD test. Results: Pullout data as a function of cement type demonstrated higher retention for conventional relative to self-adhesive cement (p < 0.001). Ti-base sandblasting (SB) favored crown retentiveness over No pretreatment (p < 0.001). Sterilized crowns exhibited higher pullout values than non-sterile (p=0.036). All the two- and three-factor interaction analyses corroborated with the superior adhesive strength of conventional compared to self-adhesive cement (all, p < 0.011), as well as, SB relative to No pretreatment (all, p < 0.024). While autoclave sterilization maximized bond strength when self-adhesive cement (data collapsed over surface pretreatment, p < 0.050) and No pretreatment were evaluated (data collapsed over surface pretreatment, p < 0.013), no significant difference was observed for conventional resin cement (p=0.280) and SB (p=0.878) groups. Conclusions: Conventional resin cement and/or Ti-base sandblasting increased Y-TZP crown retentiveness, with no significant influence of autoclave sterilization. Autoclaving increased retentiveness when self-adhesive cement and/or no Ti-base pretreatment were used.Keywords
This publication has 38 references indexed in Scilit:
- Meta-analysis of Bonding Effectiveness to Zirconia CeramicsJournal of Dental Research, 2014
- Microscopical and microbiologic characterization of customized titanium abutments after different cleaning proceduresClinical Oral Implants Research, 2012
- Systematic review of the survival rate and the incidence of biological, technical, and aesthetic complications of single crowns on implants reported in longitudinal studies with a mean follow‐up of 5 yearsClinical Oral Implants Research, 2012
- Cemented and screw‐retained implant reconstructions: a systematic review of the survival and complication ratesClinical Oral Implants Research, 2012
- Influence of internal-gap width and cement type on the retentive force of zirconia copings in pullout testingJournal of Dentistry, 2012
- Factors determining the retentiveness of luting agents used with metal- and ceramic-based implant componentsClinical Oral Investigations, 2012
- Retention of CAD/CAM All‐Ceramic Crowns on Prefabricated Implant Abutments: An In Vitro Comparative Study of Luting Agents and Abutment Surface AreaJournal of Prosthodontics, 2012
- Crown pull-off test (crown retention test) to evaluate the bonding effectiveness of luting agentsDental Materials, 2010
- Curing efficiency of four self-etching, self-adhesive resin cementsDental Materials, 2009
- The effects of abutment taper, length and cement type on resistance to dislodgement of cement‐retained, implant‐supported restorationsJournal of Prosthodontics, 2003