Through‐Thickness Residual Stresses, Microstructure, and Mechanical Properties of Electron Beam‐Welded CA6NM Martensitic Stainless Steel after Postweld Heat Treatment
Open Access
- 1 January 2020
- journal article
- research article
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2020 (1)
Abstract
In this study, the integrity of electron beam‐ (EB‐) welded CA6NM—a grade of 13% Cr‐4% Ni martensitic stainless steel—was assessed through the entire joint thickness of 90 mm after postweld heat treatment (PWHT). The joints were characterized by examining the microstructure, residual stresses, global mechanical properties (static tensile, Charpy impact, and bend), and local properties (yield strength and strain at fracture) in the metallurgically modified regions of the EB welds. The applied PWHT tempered the “fresh” martensite present in the microstructure after welding, which reduced sufficiently the hardness (<280 HV) and residual stresses (<100 MPa) to meet the requirements for hydroelectric turbine assemblies. Also, the properties of the EB joints after PWHT passed the minimum acceptance criteria specified in ASME sections VIII and IX. Specifically, measurement of the global tensile properties indicated that the tensile strengths of the EB welds in the transverse and longitudinal directions were on the same order as that of the base metal (BM). Evaluation of the local tensile properties using a digital image correlation (DIC) methodology showed higher local yield strengths in the fusion zone (FZ) and heat‐affected zone (HAZ) of 727 MPa and 740 MPa, respectively, relative to the BM value of 663 MPa. Also, the average impact energies for the FZ and HAZ were 63 J and 148 J, respectively, and attributed to the different failure mechanisms in the HAZ (dimples) versus the FZ (quasi‐cleavage consisting of facets and dimples). This study shows that the application of PWHT plays an important role in improving the weld quality and performance of EB‐welded CA6NM and provides the essential data for validating the design and manufacturing process for next‐generation hydroelectric turbine products.Keywords
Funding Information
- Natural Sciences and Engineering Research Council of Canada
- National Research Council Canada
This publication has 25 references indexed in Scilit:
- Residual Stresses, Microstructure, and Mechanical Properties of EB-Welded 90-mm-Thick UNS S41500 Martensitic Stainless Steel after PWHTMaterials Performance and Characterization, 2019
- Mehanical Properties of Electron Beam Welded Joints in Thick Gage CA6NM Stainless SteelJournal of Materials Engineering and Performance, 2017
- Mechanical properties of electron beam welds in heavy-section UNS S41500 martensitic stainless steelThe International Journal of Advanced Manufacturing Technology, 2017
- Distortion and residual stresses in electron beam-welded hydroelectric turbine materialsScience and Technology of Welding and Joining, 2016
- Global and local characteristics of an autogenous single pass electron beam weld in thick gage UNS S41500 steelMaterials Science and Engineering: A, 2016
- Characteristics of an autogenous single pass electron beam weld in thick gage CA6NM steelThe International Journal of Advanced Manufacturing Technology, 2015
- Controlling the Cut in Contour Residual Stress Measurements of Electron Beam Welded Ti-6Al-4V Alloy PlatesExperimental Mechanics, 2012
- Modelling of flow-induced stresses in a Francis turbine runnerAdvances in Engineering Software, 2010
- Effects of electron beam local post-weld heat-treatment on the microstructure and properties of 30CrMnSiNi2A steel welded jointsJournal of Materials Processing Technology, 2002
- Cross-Sectional Mapping of Residual Stresses by Measuring the Surface Contour After a CutJournal of Engineering Materials and Technology, 2000