Femoral shaft bowing in the coronal plane has more significant effect on the coronal alignment of TKA than proximal or distal variations of femoral shape
- 24 April 2014
- journal article
- Published by Wiley in Knee Surgery, Sports Traumatology, Arthroscopy
- Vol. 23 (7) , 1936-1942
Abstract
Purpose: The aim of this study was to determine (1) variations in the shape of the proximal, middle, and distal femur in a series of Korean patients who had undergone total knee arthroplasty (TKA), (2) the preoperative relationship between these three parameters and the distal valgus cutting angle referenced off the femoral intramedullary guide, and (3) whether there was any relationship between femoral bowing and variations in the shape of the proximal or distal femur in the coronal plane.Methods: The preoperative long‐standing anteroposterior radiographs of 316 consecutive osteoarthritis patients who underwent primary TKA from 2009 to 2011 were examined. The femoral neck shaft angle, the femoral shaft bowing angle, and the mechanical lateral distal femoral angle were measured to assess the shape of the proximal, middle, and distal femur, respectively. The valgus cutting angle of the femur was defined as the angle between the distal anatomical and mechanical axes of the femur.Results: The study population showed large variations in femoral shape. The mean femoral intramedullary guide angle was 6.5° ± 1.3° (range: 4°–13°). The femoral shaft bowing angle was the factor that showed the strongest correlation with this angle (P < 0.001). The mechanical lateral distal femoral angle showed only a weak correlation (P = 0.001), and the femoral neck shaft angle showed no correlation (n.s.). The femoral shaft bowing angle showed a weak correlation with the mechanical lateral distal femoral angle (P = 0.001), but was not significantly correlated with the femoral neck shaft angle (n.s.). Apparent femoral bowing (>3° of lateral or medial bowing) was found in 42 (13.3 %) of cases (37 cases of lateral bowing and five of medial bowing). Cases with lateral apparent femoral bowing >3° had a distal cutting angle of 8.6° ± 2.2° relative to the femoral intramedullary guide.Conclusion: The femoral intramedullary guide angle was mainly influenced by femoral shaft bowing among femoral deformities in the coronal plane. Therefore, to increase the accuracy of distal femoral cut during TKA, it is necessary to confirm femoral deformities and to measure the femoral intramedullary guide angle preoperatively from coronal radiographs covering the whole femur.Level of evidence: IV.Keywords
Funding Information
- National Research Foundation of Korea
- Ministry of Education, Science and Technology (2012‐0000479)
This publication has 33 references indexed in Scilit:
- Reliability of computer-assisted surgery as an intraoperative ruler in navigated high tibial osteotomyArchives of orthopaedic and trauma surgery, 2010
- What should be considered in using standard knee radiographs to estimate mechanical alignment of the knee?Osteoarthritis and Cartilage, 2010
- Longitudinal Shapes of the Tibia and Femur are Unrelated and VariableClinical Orthopaedics and Related Research, 2009
- Bony Landmarks for Determining the Mechanical Axis of the Femur in the Sagittal Plane during Total Knee ArthroplastyClinics in Orthopedic Surgery, 2009
- Is there an alternative to the full‐leg radiograph for determining knee joint alignment in osteoarthritis?Arthritis Care & Research, 2006
- A comparative assessment of alignment angle of the knee by radiographic and physical examination methodsArthritis & Rheumatism, 2005
- Alignment in total knee arthroplastyThe Journal of Bone and Joint Surgery. British volume, 2004
- Anatomic variations should be considered in total knee arthroplastyJournal of Orthopaedic Science, 2000
- Effect of Rotation on the Axial Alignment of the FemurClinical Orthopaedics and Related Research, 1989
- Alignment in Total Knee ArthroplastyClinical Orthopaedics and Related Research, 1983