A Biomechanical Comparison of Single and Double-Row Fixation in Arthroscopic Rotator Cuff Repair
Authors:
- Susan AlexanderSASusan Alexander
- Adam M. HillAHAdam M. Hill
- Pol E. HuijsmansPHPol E. Huijsmans
- Anthony M.J. BullABAnthony M.J. Bull
- Andrew A. AmisAAAndrew A. Amis
- Joe F. De BeerJBJoe F. De Beer
- Andrew L. WallaceAWAndrew L. Wallace
- 1 November 2006
- journal article
- research article
- Published by Wolters Kluwer Health in Journal of Bone and Joint Surgery
- Vol. 88 (11) , 2425-2431
Abstract
Background: The optimal method for arthroscopic rotator cuff repair is not yet known. The hypothesis of the present study was that a double-row repair would demonstrate superior static and cyclic mechanical behavior when compared with a single-row repair. The specific aims were to measure gap formation at the bone-tendon interface under static creep loading and the ultimate strength and mode of failure of both methods of repair under cyclic loading. Methods: A standardized tear of the supraspinatus tendon was created in sixteen fresh cadaveric shoulders. Arthroscopic rotator cuff repairs were performed with use of either a double-row technique (eight specimens) or a single-row technique (eight specimens) with nonabsorbable sutures that were double-loaded on a titanium suture anchor. The repairs were loaded statically for one hour, and the gap formation was measured. Cyclic loading to failure was then performed. Results: Gap formation during static loading was significantly greater in the single-row group than in the double-row group (mean and standard deviation, 5.0 ± 1.2 mm compared with 3.8 ± 1.4 mm; p < 0.05). Under cyclic loading, the double-row repairs failed at a mean of 320 ± 96.9 N whereas the single-row repairs failed at a mean of 224 ± 147.9 N (p = 0.058). Three single-row repairs and three double-row repairs failed as a result of suture cut-through. Four single-row repairs and one double-row repair failed as a result of anchor or suture failure. The remaining five repairs did not fail, and a midsubstance tear of the tendon occurred. Conclusions: Although more technically demanding, the double-row technique demonstrates superior resistance to gap formation under static loading as compared with the single-row technique. Clinical Relevance: A double-row reconstruction of the supraspinatus tendon insertion may provide a more reliable construct than a single-row repair and could be used as an alternative to open reconstruction for the treatment of isolated tears.Keywords
This publication has 12 references indexed in Scilit:
- Biomechanical Comparison of a Single-Row versus Double-Row Suture Anchor Technique for Rotator Cuff RepairThe American Journal of Sports Medicine, 2006
- Passive tension and gap formation of rotator cuff repairsJournal of Shoulder and Elbow Surgery, 2004
- Effects of freezing/thawing on the biomechanical properties of human tendonsSurgical and Radiologic Anatomy, 2001
- Experimental Rotator Cuff Repair. A Preliminary Study*Journal of Bone and Joint Surgery, 1999
- Passive tension in the supraspinatus musculotendinous unit after long-standing rupture of its tendon: A preliminary reportJournal of Shoulder and Elbow Surgery, 1998
- Nicky's knot‐‐a new slip knot for arthroscopic surgeryArthroscopy, 1998
- Strength of Fixation with Transosseous Sutures in Rotator Cuff Repair*Journal of Bone and Joint Surgery, 1997
- A Biomechanical Evaluation Of Suture Anchors In Repair Of The Rotator CuffThe Journal of Bone and Joint Surgery. British volume, 1997
- The deadman theory of suture anchors: observations along a South Texas fence lineArthroscopy, 1995
- The cryo-jaw, a clamp designed for in vitro rheology studies of horse digital flexor tendonsJournal of Biomechanics, 1982