Investigation of Sn‐Zn‐Bi solders – Part I: surface tension, interfacial tension and density measurements of SnZn7Bi solders
- 29 June 2010
- journal article
- Published by Emerald Publishing in Soldering & Surface Mount Technology
- Vol. 22 (3) , 10-16
Abstract
Purpose: The purpose of Part I of this paper is to investigate the influence of Bi additions on the surface tension, the interfacial tension, and the density of SnZn7Bi alloys (Bi=1 and 3 percent by mass) as a continuation of similar previous studies on Bi and Sb additions to the binary Sn‐Zn alloy. The main aim of Part I is to indicate that the lowering of the surface tension and interfacial tension is not sufficient for practical applications. However, knowledge of the interfacial tension between the soldering flux and the solder is necessary to convert the wetting force into the contact angle. This will be documented in Part II.Design/methodology/approach: The maximum bubble method was applied for the surface tension and the Miyazaki method was applied for the surface tension and the interfacial tension, using the density values from the dilatometric technique. The experimental surface tension results are compared with the Butler's thermodynamic modeling results and are discussed by means of the analysis of variance (ANOVA).Findings: On the basis of previous studies on Sn‐Zn‐Bi‐Sb alloys, the addition of Bi to SnZn7 slightly decreased the surface tension measured in an Ar+H2atmosphere, similarly to the Butler's modeling results. Also, a similar slight decrease of the surface tension from the Miyazaki method measured in air and in nitrogen was observed, as well as a more significant lowering of the interfacial tension with the use of a flux in nitrogen. There was also a slight influence of the temperature on the numerical values of the surface tensions and the interfacial tension. In the ANOVA, taking into account the Bi content, the temperature of measurements, the atmosphere and the flux, the flux used was shown as the most important, and also, to a lesser extent, the atmosphere.Research limitations/implications: It is intended (the purpose of Part II of this paper) to verify the positive influence of Bi additions in SnZn7 alloys on the surface tensions and the interfacial tensions via the contact angles from the interaction with Cu on printed circuit board with different lead‐free finishes.Practical implications: It is suggested that further studies on more efficient fluxes are necessary for the practical application being in agreement with the ANOVA and the literature information.Originality/value: A slight improvement of the wettability with the use of Bi additions in the SnZn7Bi alloys in the course of various experimental techniques is proven, similar to results reported in various references. The obtained results will enlarge the SURDAT database of lead‐free soldering materials.Keywords
This publication has 13 references indexed in Scilit:
- Evaluation of the influence of Bi and Sb additions to Sn‐Ag‐Cu and Sn‐Zn alloys on their surface tension and wetting properties using analysis of variance – ANOVASoldering & Surface Mount Technology, 2008
- Thermodynamic assessment of the Bi–Sn–Zn SystemCalphad, 2007
- On the advantages of using a hypoeutectic Sn–Zn as lead-free solder materialMaterials Letters, 2007
- Lead‐free Electronics2006
- Surface tension and viscosity of Sn‐based binary liquid alloysPhysica Status Solidi (a), 2005
- Properties of low melting point Sn–Zn–Bi soldersJournal of Alloys and Compounds, 2005
- Effect of composition and cooling rate on microstructure and tensile properties of Sn–Zn–Bi alloysJournal of Alloys and Compounds, 2003
- Microstructure of solder joints with electronic components in lead‐free soldersSoldering & Surface Mount Technology, 1998
- The surface tension of binary liquid mixtures: lead + tin and lead + indium alloysTransactions of the Faraday Society, 1957
- The thermodynamics of the surfaces of solutionsProceedings of the Royal Society of London. Series A, Containing Papers of a Mathematical and Physical Character, 1932