Analysis of the characteristics of periodontal curettes used for scaling the roof of the furcation by manual versus digital method
Authors:
- Larissa Porcaro SalomãoLSLarissa Porcaro Salomão
- Marcela Morgana Teixeira da SilvaMSMarcela Morgana Teixeira da Silva
- Alessandra Areas e SouzaASAlessandra Areas e Souza
- Gabriela Alessandra da Cruz Galhardo CamargoGCGabriela Alessandra da Cruz Galhardo Camargo
- Eliane Marçon BarrosoEBEliane Marçon Barroso
- Elizangela Cruvinel ZuzaEZElizangela Cruvinel Zuza
Open Access
- 1 January 2021
- journal article
- research article
- Published by FapUNIFESP (SciELO) in Revista de Odontologia da UNESP
- Vol. 50
Abstract
Introduction The treatment of periodontal disease in multiradicular teeth with furcation involvement is a challenge for dentists, with unpredictable results. Objective To evaluate the characteristics of the active tip of periodontal curettes used for scaling the furcation roof, comparing the manual versus digital method. Material and method Forty-two Pádua Lima (PL) curettes of the Millennium® brand (n = 6 for each model) were evaluated: PL 1-2, PL 3-4, PL 5-6, PLW 1-2, PLW 3-4, PLW 5 -6, and PLF. The following were measured: total length of the coronary face (CTc, millimeters, mm), total length of the lateral face (CTl, mm), width of the coronary face (Lc, mm), and width of the lateral face (Ll, mm). The measurements were performed in duplicate. Result The results showed that weight varied among the curettes (p 0.05). Considering that seven different types of curettes were evaluated, the parameters of CTl and Ll showed a statistical difference for all evaluated curettes (7: 7 ratio), with higher values for the caliper method compared to the software (p <0.05). There was a statistically significant difference between assessment methods for CTc and Lc measurements (p <0.05), showing that there was a coincidence of values in the proportion of 4:7 for measurements of CTc and 5:7 for Lc. Conclusion The comparison between methods generally resulted in lower values and greater variation for the digital method, thus favoring the use of the manual method to measure the active tip of periodontal curettes.Keywords
This publication has 11 references indexed in Scilit:
- Root surface alterations following manual and mechanical scaling: A comparative studyInternational Journal of Dental Hygiene, 2018
- OPEN-SOURCE SOFTWARE IN DENTISTRY: A SYSTEMATIC REVIEWInternational Journal of Technology Assessment in Health Care, 2017
- Open source EMR software: Profiling, insights and hands-on analysisComputer Methods and Programs in Biomedicine, 2014
- Molar furcation entrance and its relation to the width of curette blades used in periodontal mechanical therapyInternational Journal of Dental Hygiene, 2009
- Prevalence of Different Types of Accessory Canals in the Furcation Area of Third MolarsJournal of Periodontology, 2006
- Morphometric Analysis of the Furcation Anatomy of Mandibular MolarsJournal of Periodontology, 2004
- The morphology of root fusion in Chinese adults (I). Grades, types, location and distributionJournal of Clinical Periodontology, 1994
- The Effectiveness of Scaling and Root Planing With Curets Designed for Deep PocketsJournal of Periodontology, 1992
- Periodontal Implications of Furcation Entrance Dimensions in Chinese First Permanent MolarsJournal of Periodontology, 1991
- Relationship between Periodontal Furcation Involvement and Molar Cervical Enamel ProjectionsJournal of Periodontology, 1987