Feasibility Study for the Remanufacturing of H13 Steel Heat-Treated TBM Disc Cutter Rings with Uniform Wear Failure Using GMAW
Open Access
Abstract
Given that the heat treatment states of the base metal have a great influence on the surfacing repair layer, this paper carried out a feasibility study for the remanufacturing of the failed cutter rings of TBM disc cutters with uniform wear (hereinafter referred to as normally-worn ring) using the gas metal arc welding technology (GMAW). Firstly, this paper developed a heat treatment process route for H13 steel cutter rings. Secondly, the heat treatment process is numerically analyzed based on the developed route, and the rationality of the route is verified from the distribution characteristics of temperature, phase, and stress fields. Subsequently, heat treatment tests were carried out, and the physical and mechanical properties of the base metal samples prepared under laboratory conditions were evaluated respectively and systematically. Based on the comprehensive performance evaluation value calculated by the weighted comparative analysis method, it was clear that the comprehensive performance of the quenched base metal samples was 7.6% higher than that of the engineering cutter ring interior. Therefore, it is reasonable to replace the failed engineering cutter rings repaired under laboratory conditions with the prepared samples as economical alternatives. Finally, the remanufacturing of the base metal samples using GMAW was carried out, and then the remanufacturing performance of the base metal samples was analyzed. The study concluded that the comprehensive performance of the surfacing repair layer was slightly lower than that of the engineering cutter ring edge (4.1%), thus proving that the idea of surfacing remanufacturing of the normally-worn ring proposed in this paper was basically feasible.Keywords
Funding Information
- National Natural Science Foundation of China (51704256, 11832016, 52075465, 52005179, 2021RC2094, 2020RC4038, 22B0127, 2021YFB4000800, 2021ZKKF043, 2020JJ5365)
- science and technology innovation Program of Hunan Province (51704256, 11832016, 52075465, 52005179, 2021RC2094, 2020RC4038, 22B0127, 2021YFB4000800, 2021ZKKF043, 2020JJ5365)
- Excellent Youth Project of Hunan Provincial Department of Education (51704256, 11832016, 52075465, 52005179, 2021RC2094, 2020RC4038, 22B0127, 2021YFB4000800, 2021ZKKF043, 2020JJ5365)
- National key research and development program (51704256, 11832016, 52075465, 52005179, 2021RC2094, 2020RC4038, 22B0127, 2021YFB4000800, 2021ZKKF043, 2020JJ5365)
- Hefei general machinery research institute Co., LTD project (51704256, 11832016, 52075465, 52005179, 2021RC2094, 2020RC4038, 22B0127, 2021YFB4000800, 2021ZKKF043, 2020JJ5365)
- Hunan Provincial Natural Science Foundation of China (51704256, 11832016, 52075465, 52005179, 2021RC2094, 2020RC4038, 22B0127, 2021YFB4000800, 2021ZKKF043, 2020JJ5365)
This publication has 22 references indexed in Scilit:
- Failure analysis on the fracture of disc cutter in EPB shield machineEngineering Failure Analysis, 2020
- Optimum Design and Application Research of Eddy Current Sensor for Measurement of TBM Disc Cutter WearSensors, 2019
- A Hybrid Process Integrating Reverse Engineering, Pre-Repair Processing, Additive Manufacturing, and Material Testing for Component RemanufacturingMaterials, 2019
- Prediction Model of TBM Disc Cutter Wear During Tunnelling in Heterogeneous GroundRock Mechanics and Rock Engineering, 2018
- Emergy based sustainability evaluation of remanufacturing machining systemsEnergy, 2018
- Experimental study of specific matching characteristics of tunnel boring machine cutter ring properties and rockWear, 2017
- Mechanical response of surrounding rock of tunnels constructed with the TBM and drill-blasting methodNatural Hazards, 2012
- EXPERIMENTAL STUDIES ON THE MICROSTRUCTURE AND HARDNESS OF LASER TRANSFORMATION HARDENING OF LOW ALLOY STEELTransactions of the Canadian Society for Mechanical Engineering, 2012
- Development pattern and enhancing system of automotive components remanufacturing industry in ChinaResources, Conservation and Recycling, 2011
- Impact and wear resistance of polymer nanocomposites at low filler contentPolymer Engineering & Science, 2002