Stress–Strain Engineering with Lithium Solid Solution/Lithium Alloy Composite Anodes for Stable Lithium‐Metal Batteries
Authors:
Open Access
- 23 September 2025
- journal article
- Published by Wiley in Advanced Science
- Vol. 12 (46) , e15264
Abstract
High‐performance thin lithium (Li) metal anodes are indispensable for high‐energy‐density Li metal batteries, yet their electrochemical‐mechanical instability precipitates rapid failure. Uncontrolled lithium plating, accompanied by severe side reactions and the formation of a porous, non‐compact deposit, swells the electrode and generates destructive stress. An in situ investigation of stress, strain, and their spatial distributions during charge/discharge cycling identifies the coupled volume variation and stress–strain evolution as an operando descriptor of degradation and underpins the rational design of a dual‐phase Li−Ag solid‐solution/Li 22 Sn 5 alloy composite anode. Ag in Li−Ag solid solution enhances the affinity with Li + for uniform Li plating, whereas a rigid, ion‐permeable Li 22 Sn 5 scaffold confines volume expansion. LiNi 0.6 Co 0.2 MnO 0.2 (NCM622)||Li−Ag/Li 22 Sn 5 pouch cell exhibits a markedly lower internal‐pressure rise during cycling than NCM622||Li counterpart under identical conditions. Specifically, the latter shows a 58% higher pressure increase than the NCM622||Li−Ag/Li 22 Sn 5 pouch cell after charging from 0% to 100% SOC in the 5th cycle. The 1.3 Ah laminated NCM622||Li−Ag/Li 22 Sn 5 (40 µm‐thick anode) pouch cell retains 87% capacity over 100 cycles when operating at an industry‐relevant N/P ratio of 1.5 and electrolyte budget of 2.6 g Ah −1 . Mechanical‐electrochemical coupling of Li metal anode design, therefore, offers a practical route to long‐lifespan Li metal batteries.Keywords
Funding Information
- China Postdoctoral Science Foundation (2025M770137)
- National Natural Science Foundation of China (52272207)
This publication has 44 references indexed in Scilit:
- Fast‐Charging High‐Energy‐Density Lithium Metal Pouch Cells Achieved Through the In Situ Formation of Inter‐Bridged Micrometer‐Scale Li‐Al Alloy ArchitectureAdvanced Functional Materials, 2025
- In Situ‐Constructed Multifunctional Composite Anode with Ultralong‐Life Toward Advanced Lithium‐Metal BatteriesAdvanced Materials, 2024
- Operando Spatial Pressure Mapping Analysis for Prototype Lithium Metal Pouch Cells Under Practical ConditionsAdvanced Science, 2023
- Dynamic Concentration of Alloying Element on Anode Surface Enabling Cycle‐Stable Li Metal BatteriesAdvanced Functional Materials, 2023
- Locking Active Li Metal through Localized Redistribution of Fluoride Enabling Stable Li‐Metal BatteriesAdvanced Materials, 2022
- Revealing the Intrinsic Uneven Electrochemical Reactions of Li Metal Anode in Ah‐Level Laminated Pouch CellsAdvanced Functional Materials, 2022
- A Salt‐in‐Metal Anode: Stabilizing the Solid Electrolyte Interphase to Enable Prolonged Battery CyclingAdvanced Functional Materials, 2021
- Structural Evolution upon Delithiation/Lithiation in Prelithiated Foil Anodes: A Case Study of AgLi Alloys with High Li Utilization and Marginal Volume VariationAdvanced Energy Materials, 2021
- Stack Pressure Considerations for Room‐Temperature All‐Solid‐State Lithium Metal BatteriesAdvanced Energy Materials, 2019
- 30 Years of Lithium‐Ion BatteriesAdvanced Materials, 2018