Low frequency piezoelectric P(VDF-TrFE) micro-cantilevers with a novel MEMS process for vibration sensor and energy harvester applications
Authors:
- Rashmi K RRRRashmi K R
- Arjun Sunil RaoARArjun Sunil Rao
- Jayarama AJAJayarama A
- Richard PintoRPRichard Pinto
- 10 May 2019
- journal article
- research article
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 28 (6) , 065022
Abstract
Low frequency piezoelectric P(VDF-TrFE) micro-cantilever vibration sensors have been developed for the first time with a novel MEMS process. Design and simulation of micro-cantilevers were carried out using COMSOL Multiphysics based on finite element method. Frequencies and device dimensions were determined based on simulation results. The design was implemented on 〈110〉 Si wafer using a specially developed bulk micromachining process. Micro-cantilevers were fabricated with 2.5 μ m thick P(VDF-TrFE) co-polymer film deposited by spin coating technique; electrodes for power output were formed by sequential thermal evaporation of Cr-Au thin films. The two critical process steps used for the suspension of P(VDF-TrFE) micro-cantilevers are: (1) bulk micromachining of silicon from the backside using anisotropic wet etchant TMAH to define the micro-cantilever suspension regions, and (2) CHF 3 /O 2 based plasma etching of SiO 2 from backside for the final release of P(VDF-TrFE) micro-cantilevers. These devices were operated in longitudinal mode with Cr-Au interdigitated electrodes on P(VDF-TrFE) micro-cantilevers for power extraction. The experimental results obtained with laser Doppler vibrometer for micro-cantilevers with 1000 μ m length, 300 μ m width and 2.5 μ m thickness showed resonant frequency 477.03 Hz and power output 187.4 pW for tip displacement 312.5 μ m which are closely in agreement with the simulated values 453.65 Hz and 189 pW for tip displacement 310 μ m, respectively. The volume power density of this P(VDF-TrFE) unimorph micro-cantilever is 249.92 nW mm −3 , which is found to be better compared with other polymer piezoelectric cantilevers.Keywords
This publication has 53 references indexed in Scilit:
- Comparison of MEMS PZT Cantilevers Based on $d_{31}$ and $d_{33}$ Modes for Vibration Energy HarvestingJournal of Microelectromechanical Systems, 2012
- Vibration energy harvesting with aluminum nitride-based piezoelectric devicesJournal of Micromechanics and Microengineering, 2009
- Pressure sensor from a PVDF filmSensors and Actuators A: Physical, 2008
- Energy harvesting from a backpack instrumented with piezoelectric shoulder strapsSmart Materials and Structures, 2007
- Human Powered Piezoelectric Batteries to Supply Power to Wearable Electronic DevicesInternational Journal of the Society of Materials Engineering for Resources, 2002
- Electrostrictive poly(vinylidene fluoride-trifluoroethylene) copolymersSensors and Actuators A: Physical, 2001
- Strap-down microelectromechanical (MEMS) sensors for high-g munition applicationsIEEE Transactions on Magnetics, 2001
- New Piezoelectric PolymersJapanese Journal of Applied Physics, 1998
- Shear piezoelectric properties of vinylidene fluoride trifluoroethylene copolymer, and its application to transverse ultrasonic transducersApplied Physics Letters, 1995
- Spectroscopic analysis of the electric field induced structural changes in vinylidene fluoride/trifluoroethylene copolymersMacromolecules, 1989