Polydimethylsiloxane (PDMS) microfluidic modifications for cell-based immunofluorescence assay
- 12 October 2020
- journal article
- research article
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 35 (9) , 955-972
Abstract
Polydimethylsiloxane (PDMS) is a hydrophobic elastomer commonly used for microfluidic fabrication. PDMS has to be modified to improve its hydrophilicity and thus inhibits non-specific protein adsorption. This work evaluates the modification materials for the development of microfluidic cell-based immunofluorescence (IF) assay. In cell-based IF assay, PDMS is modified not just to inhibit the adsorption of non-specific florescent-conjugated protein that causes the elevation of background signal, but also to firmly support cell adhesion for subsequent immunostaining procedure. PDMS materials modified by three regular modification materials consisting of an extracellular matrix (poly-L-lysine; PLL), a hydrophilic polymer (polyvinyl alcohol; PVA) and a non- ionic surfactant (pluronic F127) were compared with each other based on hydrophilicity improvement, minimization of non-specific background signal, and enhancement of human embryonic kidney (HEK) cell adhesion. Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) analysis confirms that all modification materials are successfully immobilized on the PDMS surfaces. Due to its antifouling mechanism, pluronic modification greatly improves the hydrophilicity of the PDMS and inhibits non-specific protein adsorption. Even though the hydrophilicity and non-specific protein adsorption resistivity of the PDMS modified with PLL did not significantly differ from those of the unmodified PDMS, PLL modification obviously promotes HEK cell adhesion. Negative control and Myelin Oligodendrocyte Glycoprotein (MOG) expressing HEK cells were immobilized in microfluidics for IF assay evaluation. Results demonstrate that positive MOG expressing cells can be selectively stained by anti-MOG IgG antibody within 1 h at room temperature. Microfluidic platforms also enhance immobilized cell distribution, which compatibly supports single-cell analysis technique.Keywords
Funding Information
- Thailand’s National Science and Technology Development Agency (P-16-50098)
- Faculty of Medicine, Siriraj Hospital (r015936004)
- Thailand Research Fund
- Thailand’s National Science and Technology Development Agency (PHD/0213/2557)
This publication has 42 references indexed in Scilit:
- Sulfadiazine modified PDMS as a model material with the potential for the mitigation of posterior capsule opacification (PCO)Colloids and Surfaces B: Biointerfaces, 2013
- Thermal fracture of oxidized polydimethylsiloxane during soft lithography of nanopost arraysJournal of Micromechanics and Microengineering, 2011
- Recent developments in PDMS surface modification for microfluidic devicesElectrophoresis, 2009
- Simple poly(dimethylsiloxane) surface modification to control cell adhesionSurface and Interface Analysis, 2008
- Hydrophobic surfaces for enhanced differentiation of embryonic stem cell-derived embryoid bodiesProceedings of the National Academy of Sciences, 2008
- Stable immobilization of rat hepatocytes as hemispheroids onto collagen‐conjugated poly‐dimethylsiloxane (PDMS) surfaces: Importance of direct oxygenation through PDMS for both formation and functionBiotechnology and Bioengineering, 2007
- Hydrophilization and hydrophobic recovery of PDMS by oxygen plasma and chemical treatment—An SEM investigationSensors and Actuators B: Chemical, 2007
- Poly(vinyl alcohol) Functionalized Poly(dimethylsiloxane) Solid Surface for ImmunoassayBioconjugate Chemistry, 2007
- Detection of Cryptosporidium parvum oocysts using a microfluidic device equipped with the SUS micromesh and FITC‐labeled antibodyBiotechnology and Bioengineering, 2006
- FTIR Spectroscopic Investigation of Effects of Temperature and Concentration on PEO−PPO−PEO Block Copolymer Properties in Aqueous SolutionsMacromolecules, 2002