Optical Absorption Coefficient, Time of Thermal Relaxation, Time of Surface Threshold, and Time of Heat Incubation for PMMA Samples at the CO 2 Laser-Beam Wavelength of 10.6 µm
- 1 October 2006
- journal article
- research article
- Published by SAGE Publications in Photomedicine and Laser Surgery
- Vol. 24 (5) , 655-659
Abstract
Objective: This paper discusses in detail the mathematical identification of the optical absorption α (cm −1 ) of Beer's law, a crucial parameter to study the development of laser beam craters into dry poly(methyl methacrylate) (PMMA) samples exposed to steady CO 2 laser beams emitting radiation at λ = 10.6 µm in continuous- wave (CW) mode. Three additional time-dependent coefficients have been determined as well. In clinical applications, these results are important in order to precisely quantify and forecast the ablation capabilities of the CO 2 laser beam, to optimize its usage in the operating room, and to address the safety issues related to surgical interventions on human tissue. Background Data: Currently, the data available in the literature do not allow the identification of the numerical value of α (cm −1 ) for PMMA at λ = 10.6 µm with enough, and therefore satisfactory, accuracy. Additionally, the correct identification of the optical absorption of PMMA would allow the isolation, with better accuracy, of other key time-dependent coefficients, such as relaxation time, surface threshold time, and heat incubation time, which are all described in the literature in a qualitative rather than quantitative fashion. Correct bone cement preparation depends on the value of α(cm −1 ) of the PMMA in order to avoid unwanted complications in patients during cement removal via laser techniques. Methods: The laser in use was configured in different combinations with the following parameters: transverse electromagnetic modes (TEMnm), output power (I0), exposure times (te), and focal lengths(fk). Several PMMA blocks (1 cm × 4 cm × 4 cm) were exposed to CW radiation of three commercially available CO 2 medical laser devices showing a TEM11 mode. Each block was exposed to the beam on a horizontal and well-polished surface of each sample. Four focal lengths (2.5", 5", 7.5", and 15.75" [400 mm]) were used to focus the beam on the well-polished and dry surface of the PMMA samples. The resulting dimensions of the craters were measured after each exposure, which has been kept at a 10-Watt CW beam. Exposure time ranged from 0.5 to 2 sec. Results: The value of α = 502 (cm −1 ) for PMMAat 10.6 µm was identified, matching other results reported in the literature for similar compact media in the absence of water content, such as PMMA. The time of thermal relaxation was 9.358 · 10 −4 sec, the time of surface threshold was 9.365 · 10 −4 sec, and the time of heat incubation was 3.6 · 10 −7 sec (all three for PMMAat 10.6 µm for any exposure). Using the calculated value of α, one of the practical clinical recommendations would be, for instance, to reduce or to abolish the utilization of colorant dopants in the preparation of the bone cement mixture and therefore reduce the danger of bone damage possible during the removal of bone cement via laser techniques. Other examples refer to other clinical bone and dental treatments.Keywords
This publication has 10 references indexed in Scilit:
- Sudden and Unpredictable Below-Surface Ablation Pattern Changes by CO 2 Laser Beams: A Qualitative Description of Five Macroscopic Cases Observed in PMMA with High Probability to Occur during Surgery in Low-Water-Content TissuesJournal of Clinical Laser Medicine & Surgery, 2002
- Thermal Lesions Produced by CO 2 Laser Beams: New Findings to Improve the Quality of Minimally Invasive and Transmyocardial Laser Revascularization ProtocolsJournal of Clinical Laser Medicine & Surgery, 2000
- Excimer laser ablation of microstructures: A numerical modelJournal of Applied Physics, 1999
- A one-dimensional mathematical model of laser induced thermal ablation of biological tissueLasers in Medical Science, 1992
- Proposal of a computerized algorithm for continuous wave CO2 laser on-line control during orthopaedic surgery. Phase I: Theoretical introduction and firstin vitro trialsJournal of Clinical Monitoring and Computing, 1992
- Die Knochenzemententfernung mit dem Laser - Bone Cement Removal with the LaserBiomedical Engineering / Biomedizinische Technik, 1991
- Er:YAG laser ablation of tissue: Effect of pulse duration and tissue type on thermal damageLasers in Surgery and Medicine, 1989
- A proposed clinical application of a model of CO2laser radiation induced damage cratersJournal of Medical Engineering & Technology, 1988
- Comparison of depth and profile of osteotomies performed by rapid superpulsed and continuous-wave CO2 laser beams at high power outputJournal of Oral and Maxillofacial Surgery, 1986
- Effect of laser radiation on tissue during laser angioplastyLasers in Surgery and Medicine, 1985