Study on the microstructure and properties of Ni–Co composite coatings prepared by pulse electrodeposition with nano/micro Si 3 N 4 particles
- 6 October 2026
- journal article
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 14 (4) , 045001
Abstract
Micron silicon nitride (Si 3 N 4 ) particles are less expensive than nano silicon nitride particles. Therefore, by adjusting the ratio of micron to nano particles, can a Ni–Co composite coating with excellent overall performance be obtained while controlling cost? This study introduced mixed nano and micron Si 3 N 4 particles with different mass ratios. Ni–Co–Si 3 N 4 composite coatings were fabricated via pulse electrodeposition. The influence mechanisms of single-scale and mixed-scale particles on the microstructure, corrosion resistance, mechanical properties, and wear resistance of the coatings were investigated. Results show that nano-Si 3 N 4 particles exhibit a stronger tendency for co-deposition in the plating solution. They effectively refine grains and increase dislocation density, thereby significantly enhancing the wear resistance and mechanical properties of the coatings. The proportion of nanoparticles increased. The average grain size of the coatings refined from 16.60 nm to 12.31 nm. The dislocation density increased from 0.0046 × 10 18 m −2 to 0.0083 × 10 18 m −2 . Accordingly, the microhardness increased from 365.9 HV to 533 HV. The average friction coefficient decreased from 0.72 to 0.51, and the wear rate significantly reduced from 31.65 × 10 −9 mm 3 N·mm −1 to 2.27 × 10 −9 mm 3 N·mm −1 . However, the introduction of nano particles led to an increase in surface roughness and a decline in corrosion resistance. Micron particles exhibited certain advantages in reducing surface roughness and improving corrosion resistance. The coating prepared under this condition achieved a maximum charge transfer resistance of approximately 415 490 Ω cm 2 . In this study, the product method of specific wear rate and self-corrosion current density was used to calculate the overall performance. The S4 sample exhibited the optimal overall performance.Keywords
This publication has 40 references indexed in Scilit:
- Surface enhancement of metallic alloys by laser precision engineeringWelding in the World, 2024
- Influence of Electrodeposition Process Parameters and Si3N4 Nanoparticle Concentration on Microhardness and Wettability of Ni-Co-Si3N4 Nanocomposite CoatingsJournal of Materials Engineering and Performance, 2024
- Anti-corrosion and Microstructural Properties of Nanostructured Ni-Co Coating Prepared by Pulse-Reverse Electrochemical Deposition MethodJournal of Materials Engineering and Performance, 2023
- A review on mechanical, tribological and electrochemical performance of ceramic particle-reinforced Ni-based electrodeposited composite coatingsJournal of Materials Science, 2022
- Incorporation of nano/micron-SiC particles in Ni-based composite coatings towards enhanced mechanical and anti-corrosion propertiesInternational Journal of Minerals, Metallurgy and Materials, 2022
- The Effect of Bath pH and Temperature on the Corrosion Behavior of Co-Electrodeposited Ni-Cu/Cr2O3 Nanocomposite CoatingsJournal of Materials Engineering and Performance, 2020
- Microstructural characterization and enhanced hardness, wear and antibacterial properties of a powder metallurgy SiC/Ti-Cu nanocomposite as a potential material for biomedical applicationsCeramics International, 2019
- Influence of Cu coating of SiC particles on mechanical properties of Ni/SiC co-electrodeposited compositesCeramics International, 2018
- What is behind the inverse Hall–Petch effect in nanocrystalline materials?Acta Materialia, 2007
- Microstructure and properties of Ni–Co/nano-Al 2 O 3 composite coatings by pulse reversal current electrodepositionApplied Surface Science, 2006