Anisotropic Dynamic Shear Response and Shear Localization Mechanisms of TC4 Titanium Alloy under High-Strain-Rate Loading
Authors:
- H.W. YiHYH.W. Yi
- Ziqi WeiZWZiqi Wei
- Pingli MaoPMPingli Mao
- Feng WangFWFeng Wang
- Le ZhouLZLe Zhou
- Zhi WangZWZhi Wang
- Xiaoxu WuXWXiaoxu Wu
- Pengyu WangPWPengyu Wang
- Shimeng LiuSLShimeng Liu
Preprint
- 12 October 2026
- preprint
- Published by Elsevier in SSRN Electronic Journal
Abstract
The loading direction dependent dynamic shear behavior and adiabatic shear localization of TC4 alloy was investigated using hat-shaped samples subjected to high strain-rate loading along the extrusion direction (ED) and extrusion radial direction (ERD). Dynamic shear tests were performed using a split Hopkinson pressure bar (SHPB), and the resulting adiabatic shear bands (ASBs) were characterized by electron backscatter diffraction (EBSD). Although both loading direction exhibited similar three-stage shear responses, the ERD sample showed earlier stress collapse and ASB initiation. Energy analysis further revealed that the critical dissipated energies for ASB formation were 0.133 and 0.18 MJ m-2 for the ERD and ED samples, respectively, indicating a higher adiabatic shear sensitivity under ERD loading. Consistently, EBSD revealed an ultrafine-equiaxed central area (CA) surrounded by a highly distorted transition area (TA), with the ERD sample exhibiting a narrower CA and thus more severe strain localization. The CA in both samples contained fine equiaxed grains. However, the ERD sample exhibited higher GOS and KAM values, together with a larger fraction of residual low-angle grain boundaries, indicating more extensive post-recrystallization deformation. Microstructural evidence suggests that continuous and discontinuous dynamic recrystallization jointly contribute to microstructural evolution in the TA, whereas rotational dynamic recrystallization provides a kinetically feasible pathway for the rapid formation of ultrafine equiaxed grains in the CA. Moreover, the recrystallized grains continue to accommodate localized strain during subsequent loading, leading to renewed dislocation accumulation and secondary grain refinement. These results establish a direct correlation between loading orientation, energy dissipation, shear localization, and dynamic recrystallization during high-rate deformation of TC4 alloy.Keywords
This publication has 21 references indexed in Scilit:
- A comparative study on the ability of grain and second phase homogenization to improve the corrosion resistance and pitting resistance of Mg-Zn-Nd-Zr alloyCorrosion Science, 2026
- Effect of Pre-Deformation on Adiabatic Shear Sensitivity of AZ31 Magnesium AlloyMetals and Materials International, 2025
- Enhanced dynamic compression properties of a low density near-α titanium alloy associated with deformation induced laminated microstructure and dynamic segregationActa Materialia, 2024
- Effect of α phase morphologies on shear localization behavior of TC4 titanium alloy at high strain rateJournal of Materials Science, 2024
- The effects of ultra-fine-grained structure and cryogenic temperature on adiabatic shear localization in titaniumActa Materialia, 2019
- The dynamic plasticity and dynamic failure of a magnesium alloy under multiaxial loadingActa Materialia, 2018
- Influence of texture and test velocity on the dynamic, high-strain, tensile behavior of zirconiumActa Materialia, 2012
- Correlation of adiabatic shearing behavior with fracture in Ti-6Al-4V alloys with different microstructuresInternational Journal of Impact Engineering, 2009
- Analysis of the different slip systems activated by tension in a α/β titanium alloy in relation with local crystallographic orientationActa Materialia, 2005
- Dissipation in adiabatic shear bandsMechanics of Materials, 1994