Production of AA6061-T6/Al2O3 reinforced nanocomposite using friction stir welding
Authors:
- 1 December 2019
- journal article
- research article
- Published by IOP Publishing in Engineering Research Express
- Vol. 1 (2) , 025052
Abstract
Heat-treatable AA6061-T6 weldability leads to a decline in the physio-mechanical and tribological properties due to strengthening precipitates dissolution in the nugget zone of FS-welded joints. Improvement in these properties is governed by reinforcement particles addition in the weld joint line for non-heat treatable Al-alloys. Although, its application to AA6061-T6 is scant. In the present work, FS-welded joints were produced by reinforcing Al 2 O 3 nanoparticles into the faying surface of the base matrix. The purpose of Al 2 O 3 nanoparticles addition is to refine the microstructure of the nugget zone and to obstruct the granular growing in the heat-affected zone. FSW was conducted at constant rotating 2000 rpm, transverse 70 mm min −1 speed to illustrate the influence of Al 2 O 3 addition on mechanical, microstructure, micro-hardness, and wear properties of welds compared to parent alloy and unreinforced joints. Findings revealed that Al 2 O 3 nanoparticles addition along the joint line leads to noteworthy grains refinement structure of weld zone (6 μ m) compared with the base material (38 μ m) and unreinforced nugget (18 μ m) joints. In addition, reinforced FS-W nugget zone have banded structure of alternate regions namely, nanoparticles-rich and free those have a difference in grain size, such that, the nanoparticle-rich region has fine grain size (6 μ m) than nano particle-free (14 μ m) region. Due to Zener-influence occurred via Al 2 O 3 nanoparticles helps to avoid the grain growth accompanied by dynamic recrystallization throughout FSW process which results in granular size reduction. Tensile strength (246 MPa/73%), microhardness (88HV/52%), and wear properties was notably increased for reinforced FSW joint compared to unreinforced joint (tensile strength (180MPa), micro-hardness (46 HV), and lower wear resistance, under similar parameters which attribute to nanoparticles presence in processed area. Moreover, single FSW pass leads to non-uniform distribution of Al 2 O 3 nanoparticles and nucleation of voids at Al/Al 2 O 3 boundary in the heat-affected zone which leads to early fracture of welded joint during tensile loading.Keywords
This publication has 37 references indexed in Scilit:
- Laser Surface Alloying of Aluminum (AA1200) with Ni and SiC PowdersMaterials and Manufacturing Processes, 2010
- Novel Nanoparticle‐Reinforced Metal Matrix Composites with Enhanced Mechanical PropertiesAdvanced Engineering Materials, 2007
- Effect of friction stir welding on microstructure, tensile and fatigue properties of the AA7005/10 vol.%Al2O3 compositeComposites Science and Technology, 2007
- Friction stir welding of SiC particulate reinforced AA2124 aluminium alloy matrix compositeMaterials & Design (1980-2015), 2007
- Al–Al3Ti nanocomposites produced in situ by friction stir processingActa Materialia, 2006
- Microstructures and wear property of friction stir welded AZ91 Mg/SiC particle reinforced compositeComposites Science and Technology, 2006
- Relationship between grain size and Zener–Holloman parameter during friction stir processing in AZ31 Mg alloysScripta Materialia, 2004
- Microstructural studies of friction stir welds in 2024-T3 aluminumMaterials Science and Engineering: A, 2002
- Effects of friction stir welding on microstructure of 7075 aluminumScripta Materialia, 1997
- SOLIDIFICATION BEHAVIOR OF AI-Li-SiCpMMCs PROCESSED USING VARIABLE CO-DEPOSITION OF MULTI-PHASE MATERIALSMaterials and Manufacturing Processes, 1990