Influence of electric pulse treatment on structure and hardness of cryorolled aluminum
- 1 September 2021
- journal article
- research article
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 11 (3) , 351-356
Abstract
The influence of the energy of electric pulse treatment (EPT) in the range of integral current densities (K-j) from 0.06 x 10(5) to 0.29 x 10(5) A(2)s/mm(4) on the structure and hardness of coarse-grained high-purity Al, isothermally rolled up to a total strain of 90 % at a liquid nitrogen temperature, was studied. It was found that EPT with an energy up to K-j = 0.104 x 10(5) A(2)s/mm(4) practically did not affect the microhardness obtained in the cryorolled aluminum (45 - 50 HV). An increase in the EPT energy to K-j = 0.121 x 10(5) A(2)s/mm(4) led to a rapid drop of the hardness to 30 HV followed by its gradual stabilization near 25 HV at higher K-j values. It was established that an enhanced microhardness of rolled Al resulted from formation of a well developed cellular structure with a crystallite size of about 2 mu m, containing less than 10 % of ultrafine grains of about 4 mu m in size. The minor hardness changes after EPT with K-j up to 0.104 x10(5) A(2)s/mm(4) were related to occurrence of recovery and continuous recrystallization, resulted only in improving the deformation structure without noticeable changes in its type and the crystallite sizes. Therewith the softening caused by a partial decrease in the scalar dislocation density and the microdeformation of the crystal lattice was compensated by increasing the high angle boundaries fraction. At EPT with K-j= 0.121 x 10(5) A(2)s/mm(4), the deformation structure was severely replaced by the fine-grain recrystallized one with the grain size of 19 mu m, and resulted in the loss of the strenthening effect, caused by rolling. With further increase in the EPT energy, an extensive grain growth was observed, leading to the formation of a non-uniform structure grains and to appropriate material softening, owing to the grain coarsening. It was concluded that the restoration processes that took place during EPT were similar in nature to those that occur during furnace annealing of heavily deformed materials. Therewith, the short time of the thermal exposure on the deformed metal during EPT was compensated by high applied energies.Keywords
Funding Information
- Russian Foundation for Basic Research (19-08-00953А)
This publication has 20 references indexed in Scilit:
- Cryogenic rolling-enhanced mechanical properties and microstructural evolution of 5052 Al-Mg alloyMaterials Science and Engineering: A, 2017
- Plastic deformation of FCC alloys at cryogenic temperature: the effect of stacking-fault energy on microstructure and tensile behaviourJournal of Materials Science, 2017
- Microstructure response of cryogenically-rolled Cu–30Zn brass to electric-current pulsingJournal of Alloys and Compounds, 2016
- Structure of the aluminum alloy Al-Cu-Mg cryorolled to different strainsPhysics of Metals and Metallography, 2015
- Effect of electric-current pulses on grain-structure evolution in cryogenically rolled copperJournal of Materials Research, 2014
- Role of stacking fault energy in strengthening due to cryo-deformation of FCC metalsMaterials Science and Engineering: A, 2010
- Microstructural response of pure copper to cryogenic rollingActa Materialia, 2010
- The effect of cryogenic temperature and change in deformation mode on the limiting grain size in a severely deformed dilute aluminium alloyActa Materialia, 2008
- Structure Evolution in Copper Resulting From the Effect of Powerful Current PulsesJournal of Materials Engineering and Performance, 2003
- Continuous recrystallization in austenitic stainless steel after large strain deformationActa Materialia, 2002