Mechanical Properties of Experimental Composites with Different Photoinitiator
Authors:
Open Access
- 24 August 2021
- journal article
- research article
- Published by Georg Thieme Verlag KG in European Journal of Dentistry
- Vol. 16 (01) , 167-172
Abstract
Objective The effect of different photoinitiators on mechanical properties of experimental composites was evaluated. Materials and Methods Resin composites were formulated by using a blend of bisphenol A-glycidyl and triethylene glycol (50/50 wt%) dimethacrylate monomers, and 65 wt% of barium aluminium silicate and silica filler particles. Photoinitiators used were 0.2% camphorquinone (CQ) and 0.8% co-initiator (DMAEMA); 0.2% phenyl-propanedione and 0.8% DMAEMA; 0.1% CQ + 0.1% phenyl propanedione and 0.8% DMAEMA; 0.42% mono(acyl)phosphine oxide (MAPO); and 0.5% bis(acyl)phosphine oxide (BAPO). Specimens (n = 10) were light cured by using a multiple-emission peak light-emitting diode for 20 seconds at 1,200 mW/cm2 of irradiance and Knoop hardness and plasticization, depth of cure, flexural strength, and elastic modulus were evaluated. Data were statiscally analyzed at significance level of α = 5%. Results Experimental composites containing MAPO and BAPO photoinitiators showed the highest values of flexural strength, elastic modulus, top surface hardness, and lower hardness reduction caused by alcohol compared with CQ. Composites containing CQ and PPD showed similar results, except for depth of cure and hardness of bottom surface. Conclusion BAPO and MAPO showed higher flexural strength, elastic modulus, hardness on top surface, and lower polymer plasticization to CQ. Publication Date: 24 August 2021 (online) © 2021. European Journal of Dentistry. This is an open access article published by Thieme under the terms of the Creative Commons Attribution-NonDerivative-NonCommercial-License, permitting copying and reproduction so long as the original work is given appropriate credit. Contents may not be used for commercial purposes, or adapted, remixed, transformed or built upon. (https://creativecommons.org/licenses/by-nc-nd/4.0/). Thieme Medical and Scientific Publishers Pvt. Ltd. A-12, 2nd Floor, Sector 2, Noida-201301 UP, IndiaKeywords
This publication has 42 references indexed in Scilit:
- Color stability of experimental composites containing different photoinitiatorsJournal of Dentistry, 2013
- Specimen aspect ratio and light transmission in photoactive dental resinsDental Materials, 2012
- Depth of cure of resin composites: Is the ISO 4049 method suitable for bulk fill materials?Dental Materials, 2012
- Curing efficiency of dental resin composites formulated with camphorquinone or trimethylbenzoyl-diphenyl-phosphine oxideDental Materials, 2012
- Micro-Raman spectroscopic analysis of the degree of conversion of composite resins containing different initiators cured by polywave or monowave LED unitsJournal of Dentistry, 2012
- Effect of CQ-amine ratio on the degree of conversion in resin monomers with binary and ternary photoinitiation systemsRestorative Dentistry & Endodontics, 2012
- BisGMA/TEGDMA ratio and filler content effects on shrinkage stressDental Materials, 2011
- Influence of BisGMA, TEGDMA, and BisEMA contents on viscosity, conversion, and flexural strength of experimental resins and compositesEuropean Journal of Oral Sciences, 2009
- Cross-link density evaluation through softening tests: Effect of ethanol concentrationDental Materials, 2008
- Depth of Cure of Dental Resin Composites: ISO 4049 Depth and Microhardness of Types of Materials and ShadesOperative Dentistry, 2008