Adapting the Pore Size of Individual, 3D-Printed CPC Scaffolds in Maxillofacial Surgery
Authors:
- David MuallahDMDavid Muallah
- Philipp SembdnerPSPhilipp Sembdner
- Stefan HoltzhausenSHStefan Holtzhausen
- Heike MeissnerHMHeike Meissner
- André HutskyAndré Hutsky
- Daniel EllmannDEDaniel Ellmann
- Antje AssmannAAAntje Assmann
- Matthias C. SchulzMSMatthias C. Schulz
- Günter LauerGLGünter Lauer
- Lysann M. KroschwaldLKLysann M. Kroschwald
Open Access
- 16 June 2021
- journal article
- research article
- Published by MDPI AG in Journal of Clinical Medicine
- Vol. 10 (12) , 2654
Abstract
Three dimensional (3D) printing allows additive manufacturing of patient specific scaffolds with varying pore size and geometry. Such porous scaffolds, made of 3D-printable bone-like calcium phosphate cement (CPC), are suitable for bone augmentation due to their benefit for osteogenesis. Their pores allow blood-, bone- and stem cells to migrate, colonize and finally integrate into the adjacent tissue. Furthermore, the pore size affects the scaffold’s stability. Since scaffolds in maxillofacial surgery have to withstand high forces within the jaw, adequate mechanical properties are of high clinical importance. Although many studies have investigated CPC for bone augmentation, the ideal porosity for specific indications has not been defined yet. We investigated 3D printed CPC cubes with increasing pore sizes and different printing orientations regarding cell migration and mechanical properties in comparison to commercially available bone substitutes. Furthermore, by investigating clinical cases, the scaffolds’ designs were adapted to resemble the in vivo conditions as accurately as possible. Our findings suggest that the pore size of CPC scaffolds for bone augmentation in maxillofacial surgery necessarily needs to be adapted to the surgical site. Scaffolds for sites that are not exposed to high forces, such as the sinus floor, should be printed with a pore size of 750 µm to benefit from enhanced cell infiltration. In contrast, for areas exposed to high pressures, such as the lateral mandible, scaffolds should be manufactured with a pore size of 490 µm to guarantee adequate cell migration and in order to withstand the high forces during the chewing process.Keywords
Funding Information
- Bundesministerium für Wirtschaft und Energie (ZF4379203MC8)
This publication has 47 references indexed in Scilit:
- Autologous bone graft harvesting: a review of grafts and surgical techniquesMUSCULOSKELETAL SURGERY, 2015
- Combined Effect of a Microporous Layer and Type I Collagen Coating on a Biphasic Calcium Phosphate Scaffold for Bone Tissue EngineeringMaterials, 2015
- Biomechanics and Mechanobiology of Trabecular Bone: A ReviewJournal of Biomechanical Engineering, 2015
- Calcium phosphate ceramics in bone tissue engineering: A review of properties and their influence on cell behaviorActa Biomaterialia, 2013
- Donor Site Complications in Bone Grafting: Comparison of Iliac Crest, Calvarial, and Mandibular Ramus BoneThe International Journal of Oral and Maxillofacial Implants, 2013
- Calcium phosphate cement augmentation in the treatment of depressed tibial plateau fractures with open reduction and internal fixationActa Orthopaedica et Traumatologica Turcica, 2010
- Clinical Experience of the Brushite Calcium Phosphate Cement for the Repair and Augmentation of Surgically Induced Cranial Defects Following the Pterional CraniotomyJournal of Korean Neurosurgical Society, 2010
- The issue of bioresorption of the Bio-Oss xenogeneic bone substitute in bone defects.2004
- Effect of surface roughness of hydroxyapatite on human bone marrow cell adhesion, proliferation, differentiation and detachment strengthBiomaterials, 2000
- BIO-OSS--a resorbable bone substitute?1998