This report is based on the study of a diamond-drill core through the entire gypsum-anhydrite cap rock. The anhydrite cap rock forms on top of a salt stock by cementation of anhydrite freed from the salt as a result of solution of the salt by ground water. Intermittent accumulation or compaction results in distinct layers called katatectic layers or beds, separated by katatectic surfaces. The anhydrite cap rock as thus formed is designated primary anhydrite cap rock. All changes in it or additions to it are epigenetic. Gypsification, under present conditions, probably does not take place, in the cap rock represented in the core on which this report is based, below a depth of about 1183 feet, except perhaps adjacent to faults. Gypsifying waters penetrate the cap rock either along a few widely separated fissures from which they advance on a fairly definite front, or, where deformation has been more intense, along an intimate mesh of closely spaced fissures, causing what is here called “diffuse gypsification.” Gypsification does not seem generally to have been accompanied by an increase of volume. The excess calcium sulfate must therefore have been removed. Gypsum first forms as sharply defined crystals mostly smaller than the anhydrite crystals they replace, but not necessarily falling within the limits of a single anhydrite crystal. Integration into larger crystals takes place very irregularly and complexly, but the end product is large, clear, homogeneous crystals. To explain the complexity in integration it is suggested that the water of crystallization of the gypsum acts as a medium in which the lattice of crystals is unstable so that some growing crystals can influence and reorient the lattice of other crystals at a distance. The influence of stress on integration and factors determining the boundaries of integrated crystals are briefly discussed. Along better-defined narrow fissures gypsum, instead of forming originally as equant crystals, is elongated transversely to the fissure. But it formed this way by replacement of the anhydrite adjacent to the fissure, not by growth into an open fissure. It usually forms along steep fissures that are probably due to tension, not along low-angle fissures generally associated with shear. As a result of the upward “flowage” of the salt of the salt stock, the cap rock is pushed against and through the overlying beds. “Flow” is faster in the central than in the peripheral part of the salt stock so that the cap is bent. The net results are shear and tension fissures, faults, and mylonization of the cap rock to various extents in different parts. Faulting may also result from the lowering of the salt table—the flat top of the salt stock. The effects of stress on the individual minerals of the cap are discussed. Certain minerals, especially the coarse rhombic carbonates, seem to retain evidence of deformation when recrystallization has made it difficult or impossible to recognize such evidence in the enclosing anhydrite or gypsum rock. They can therefore record past deformation. Evidence is brought out in support of the hypothesis that deformation of the anhydrite cap rock resulting in mylonization and “flowage” takes place by movement along a mesh of fissures forming a more or less rhomboidal to lenticular pattern. As deformation proceeds, the rhomboids become more and more elongate, and the fissures consequently more nearly parallel, resulting in the lenticular and braided pattern that gives the appearance of “flowage.” However, the evidence indicates that except along faults displacement of any two adjacent parts of the cap rock is slight. But deformation of the cap rock as a whole by the summation of many such small movements may be considerable. Apparently even very slight movement can result in intense mylonization. In some specimens of anhydrite rock the cleavages and the spaces between crystals have been opened up, but there is no mylonite. This is considered the first effect of stress on the rock. It gives the polished face a saccharoidal appearance. It is here called “emphasized cleavage.” Mylonization is apparently more intense below than above faults, and more intense below than above katatectic surfaces along which there has been movement. It is suggested that this is due to deformation as a result of the upward thrust of the salt, partly relieved by shearing along fault planes or katatectic surfaces. Although the forces that produce fissures cannot be sharply differentiated, there are three general types of fissures in the cap rock: shear fissures generally having low dip roughly parallel to katatectic surfaces; tension fissures, generally steep; and echelon fissures, of intermediate dip, attributed to a combination of shear and tension. Where the steep tension type of fissure formed it generally preceded the low-angle fissure, but in an association of the three types the order seemed to be echelon fissure, shear fissure, tension fissure. Two phases of recrystallization in the anhydrite cap rock are discussed. One phase reintegrates the fragments of mylonized anhydrite into larger crystals, the other results in elongation of anhydrite crystals. Criteria for the recognition of reintegrated anhydrite rock both in hand specimen and in thin section are discussed. Elongation by recrystallization is believed to take place adjacent and parallel to fissures. Random elongation is ascribed to growth parallel to the rhomboidal mesh of fissures along which “flowage” is postulated. The common, more advanced recrystallization immediately above rather than immediately below katatectic surfaces is ascribed to circulation of water upward from these surfaces. Some specimens of anhydrite rock from the deeper part of the cap show an irregular, intimate interpenetration of grains; some of these grains are crushed though there is no general mylonization. This is...