Hard Cr2O3 coatings on SS316L substrates prepared by reactive magnetron sputtering technique: a potential candidate for orthopedic implants
Authors:
- 17 April 2019
- journal article
- research article
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (20) , 25146-25154
Abstract
316L stainless steel (SS) implants suffer from tribological and biocompatibility problems which limit their service lifetime. In order to improve the surface properties of 316L SS for orthopedic implant applications, hard chromium oxide coatings were applied on 316L SS substrates using a reactive magnetron sputtering technique. The morphological, structural, and phase compositional analyses were conducted on the deposited coatings by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy. The Rockwell-C indentation tests were performed on the coated substrates to qualitatively evaluate the adhesion of coatings on the steel substrates. The surface characteristics of coatings were measured by using an optical profilometer. The mechanical properties of coatings were reported by measuring the Hardness and Young’s modulus. The corrosion resistance of coated and uncoated SS substrates was compared using potentiodynamic polarization tests. An inductively coupled plasma optical emission spectrometry (ICP-OES) was employed to analyze the biocompatibility of the samples by measuring the amount of toxic Cr ions released after the immersion test. The results show that the coatings are adherent and composed of a single Cr2O3 phase with a hardness of 25 to 29 GPa. The corrosion resistance of the SS has been improved by applying a chromium oxide coating. The coated SS samples have also demonstrated better wear resistance and lower friction coefficient compared to bare SS samples under a reciprocating sliding condition in saline solution. The biocompatibility of the SS has been enhanced by the Cr2O3 coating as much less Cr ions were released after immersion tests. These results indicate that the hard Cr2O3 coatings can be considered as a candidate for extending the lifetime of SS implants.Keywords
This publication has 47 references indexed in Scilit:
- Hardness and elastic modulus gradients in plasma-nitrided 316L polycrystalline stainless steel investigated by nanoindentation tomographyActa Materialia, 2012
- Evaluation of ion release, cytotoxicity, and platelet adhesion of electrochemical anodized 316 L stainless steel cardiovascular stentsJournal of Biomedical Materials Research Part B: Applied Biomaterials, 2008
- Microstructures and mechanical properties of chromium oxide films by arc ion platingMaterials Letters, 2004
- Tribological studies of chromium oxide films for magnetic recording applicationsThin Solid Films, 1997
- Low stress and optically transparent chromium oxide layer for x-ray mask makingJournal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena, 1993
- An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experimentsJournal of Materials Research, 1992
- Handbook of X‐ray Photoelectron Spectroscopy C. D. Wanger, W. M. Riggs, L. E. Davis, J. F. Moulder and G. E.Muilenberg Perkin‐Elmer Corp., Physical Electronics Division, Eden Prairie, Minnesota, USA, 1979. 190 pp. $195Surface and Interface Analysis, 1981
- Discussion: “Generation of Squeal/Chatter in Water-Lubricated Elastomeric Bearings” (Krauter, A. I., 1981, ASME J. Lubr. Technol., 103, pp. 406–412)Journal of Lubrication Technology, 1981
- Chromic oxide as refractory materialRefractories and Industrial Ceramics, 1977
- The infrared and Raman spectra of chromium (III) oxideSpectrochimica Acta Part A: Molecular Spectroscopy, 1968