Iridium-platinum alloy nanoparticles: Composition-dependent electrocatalytic activity for formic acid oxidation
- 24 May 2011
- journal article
- research article
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry
- Vol. 21 (25) , 9169-9178
Abstract
IrxPt100−x alloy nanoparticles with varied compositions (x = 100, 75, 67, 50, 34, and 0) were synthesized by a thermolytic process at varied ratios of the IrCl3 and PtCl2 precursors. High-resolution transmission electron microscopic (HRTEM) measurements showed that the nanoparticles all exhibited well-defined crystalline structures with the average core diameters around 2 nm; and the elemental compositions were determined by X-ray photoelectron spectroscopic (XPS) measurements. The electrocatalytic activities of the IrxPt100−x nanoparticles toward formic acid oxidation were then examined by electrochemical measurements, including cyclic voltammetry (CV), chronoamperometry, and electrochemical impedance spectroscopy (EIS). In the CV studies, it was found that both the current density of formic acid oxidation and the tolerance to CO poisoning were strongly dependent on the composition of the iridium-platinum alloy nanoparticles, with the best performance found with the Ir50Pt50 nanoparticles. Due to heavy CO poisoning, Pt nanoparticles exhibited the lowest catalytic performance among the series of nanoparticles (excluding Ir nanoparticles). The Ir50Pt50 nanoparticles also showed the maximum current density and stability in chronoamperometric measurements. Consistent results were obtained in electrochemical impedance spectroscopic studies of the electron transfer kinetics involved. Notably, of all the nanoparticle electrocatalysts, an inductive component, i.e. negative impedance, was observed in the potential windows where CO was removed by electro-oxidation; and the charge transfer resistance was found to be the lowest with the Ir50Pt50 nanoparticles. Based on the current density and peak potential of formic acid oxidation, the ratio of the anodic peak current density to the cathodic peak current density measured in CV studies, the stability manifested in chronoamperometric measurements and the tolerance to CO poisoning displayed in EIS measurements, the electrocatalytic performance of the IrPt alloy nanoparticles was found to decrease in the order of Ir50Pt50 > Ir67Pt33 > Ir75Pt25 > Ir34Pt66 > Pt. That is, among the series of IrPt alloy nanoparticles, the sample with the Ir/Pt atomic ratio of 1 : 1 showed the highest electrocatalytic activity towards formic acid oxidation, which might be ascribed to the bifunctional reaction mechanism of bimetallic alloy electrocatalysts.Keywords
This publication has 66 references indexed in Scilit:
- Platinum−Gold Nanoparticles: A Highly Active Bifunctional Electrocatalyst for Rechargeable Lithium−Air BatteriesJournal of the American Chemical Society, 2010
- Platinum-Based Nanostructured Materials: Synthesis, Properties, and ApplicationsChemical Reviews, 2010
- Synthesis of Tetrahexahedral Platinum Nanocrystals with High-Index Facets and High Electro-Oxidation ActivityScience, 2007
- Electro-oxidation of formic acid catalyzed by FePt nanoparticlesPhysical Chemistry Chemical Physics, 2006
- High power density direct formic acid fuel cellsJournal of Power Sources, 2004
- Direct formic acid fuel cellsJournal of Power Sources, 2002
- Materials for fuel-cell technologiesNature, 2001
- Methanol oxidation and direct methanol fuel cells: a selective reviewJournal of Electroanalytical Chemistry, 1999
- Fuel cells for transportationJournal of Power Sources, 1990
- Analysis of adsorbed intermediates and determination of surface potential shifts by demsElectrochimica Acta, 1986