In Situ synthesis of multiblock copolymers of poly(ϵ‐caprolactone) with different poly(ether diols) based polyurethane by reactive extrusion
Authors:
- 23 November 2011
- journal article
- research article
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 124 (5) , 3765-3773
Abstract
Polyurethanes with multiblock copolymers of poly(ϵ‐caprolactone) (PCL) and poly(tetramethylene oxide) glycol (PTMG) or poly(ethylene glycol) (PEG) as a soft segment were synthesized in situ via reactive extrusion from ϵ‐caprolactone (CL) and 4,4′‐diphenylmethane diisocyanate (MDI). The titanium alkoxide mixture generated from an ester‐exchange reaction between titanium propoxide [Ti(OPr)4], and excessive PTMG or PEG was used as an initiator and catalyst. Compared to the reported fabrication of polycaprolactone‐based polyurethane (PCLU), the in situ reactive extrusion preparation not only explored a new rapid route for the fabrication of PCLU but also offered a simplified, controllable approach for the production of PCLU in a successive mass scale. A series of PTMG–PCLUs and PEG–PCLUs with different PCL block‐average degrees of polymerization (DPn's) were prepared by only an adjustment of the relative concentration of CL in the reaction system, with a certain constant molar ratio of MDI to titanium alkoxide. 1H‐NMR, gel permeation chromatography, and differential scanning calorimetry results indicate that all of the CL monomers were converted in the polymerization, and the molecular weight of the copolymers was about 8 × 104 g/mol with a polydispersity index of approximate 2.4. With an increase in the PCL block‐average DPn in PTMG–PCLU from 25 to 40, the tensile strength increased from 16.5 to 22.7 MPa, and the melting point increased from 46.1 to 49.5°C. It was also verified by PEG–PCLU prepared with organic Ti of lowered content in the initiator mixture that the mechanical properties could be greatly affected and dropped with decreasing content of organic Ti in the initiator mixture. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012Keywords
This publication has 21 references indexed in Scilit:
- The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanesJournal of Polymer Science Part B: Polymer Physics, 2007
- Synthesis and properties of novel biodegradable poly(ε‐caprolactone)/ poly(ethylene glycol)‐based polyurethane elastomersPolymer International, 2006
- Synthesis and properties of biodegradable elastomeric epoxy modified polyurethanes based on poly(ε-caprolactone) and poly(ethylene glycol)European Polymer Journal, 2005
- Uncatalyzed synthesis, thermal and mechanical properties of polyurethanes based on poly(-caprolactone) and 1,4-butane diisocyanate with uniform hard segmentBiomaterials, 2005
- Poly(ε-caprolactone) Polyurethane and Its Shape-Memory PropertyBiomacromolecules, 2005
- Study of the Synthesis, Crystallization, and Morphology of Poly(ethylene glycol)−Poly(ε-caprolactone) Diblock CopolymersBiomacromolecules, 2004
- Reactive extrusion of poly(urethane‐isocyanurate)Advances in Polymer Technology, 2004
- Thermal degradation of poly[(R)-3-hydroxybutyrate], poly[ε-caprolactone], and poly[(S)-lactide]Polymer Degradation and Stability, 2002
- A Strategy for Increasing Molecular Weight of Polyester by Lipase-Catalyzed PolymerizationChemistry Letters, 2001
- Biodegradable block copolymers as injectable drug-delivery systemsNature, 1997