Facile encapsulation of cyanoacrylate-based bioadhesive by electrospray method and investigation of the process parameters
Open Access
- 5 March 2024
- journal article
- research article
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-12
Abstract
Polymer microcapsules containing cyanoacrylates have represented a promising option to develop self-healing biomaterials. This study aims to develop an electrospray method for the preparation of capsules using poly(methyl methacrylate) (PMMA) as the encapsulant and ethyl 2-cyanoacrylate (EC) as the encapsulate. It also aims to study the effect of the electrospray process parameters on the size and morphology of the capsules. The capsules were characterized using Fourier-transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and field-emission scanning electron microscopy (FE-SEM). Moreover, the effects of electrospray process parameters on the size were investigated by Taguchi experimental design. FTIR and TGA approved the presence of both PMMA and EC without further reaction. FE-SEM micrograph demonstrated that an appropriate choice of solvents, utilizing an appropriate PMMA:EC ratio and sufficient PMMA concentration are critical factors to produce capsules dominantly with an intact and spherical morphology. Utilizing various flow rates (0.3–0.5 ml/h) and applied voltage (18–26 kV), capsules were obtained with a 600–1000 nm size range. At constantly applied voltages, the increase in flow rate increased the capsule size up to 40% (ANOVA, p ≤ 0.05), while at constant flow rates, the increase in applied voltage reduced the average capsule size by 3.4–26% (ANOVA, p ≤ 0.05). The results from the Taguchi design represented the significance of solution flow rate, applied voltage, and solution concentration. It was shown that the most effective parameter on the size of capsules is flow rate. This research demonstrated that electrospray can be utilized as a convenient method for the preparation of sub-micron PMMA capsules containing EC. Furthermore, the morphology of the capsules is dominated by solvents, PMMA concentration, and PMMA:EC ratio, while the average size of the capsules can be altered by adjusting the flow rate and applied voltage of the electrospray process.Keywords
Funding Information
- Lulea University of Technology
This publication has 47 references indexed in Scilit:
- Doxorubicin/poly(caprolactone)/polyethylene glycol nanoparticles prepared by electrosprayPolymers for Advanced Technologies, 2023
- Self‐healing performance of hybrid core‐shell nanofibers mat containing epoxy‐mercaptan at subroom temperaturePolymer Composites, 2021
- The influence of size and healing content on the performance of extrinsic self‐healing coatingsJournal of Applied Polymer Science, 2020
- Material encapsulation in poly(methyl methacrylate) shell: A reviewJournal of Applied Polymer Science, 2019
- Introduction to the Taguchi Method2018
- Extended fatigue life of a catalyst free self‐healing acrylic bone cement using microencapsulated 2‐octyl cyanoacrylateJournal of Biomedical Materials Research Part B: Applied Biomaterials, 2014
- In vitro response to alkaline phosphatase coatings immobilized onto titanium implants using electrospray deposition or polydopamine‐assisted depositionJournal of Biomedical Materials Research Part A, 2013
- Microencapsulation of 2‐octylcyanoacrylate tissue adhesive for self‐healing acrylic bone cementJournal of Biomedical Materials Research Part B: Applied Biomaterials, 2012
- Encapsulation of a glycosaminoglycan in hydroxyapatite/alginate capsulesJournal of Biomedical Materials Research Part A, 2008
- Biomimetic pH Sensitive Polymersomes for Efficient DNA Encapsulation and DeliveryAdvanced Materials, 2007