Research on the machined surface integrity under combination of various inclination angles in multi-axis ball end milling
- 16 August 2013
- journal article
- research article
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 228 (1) , 31-50
Abstract
It is well known that the multi-axis machining technology has been developed into a key technique applied in the manufacturing field. The machined surface integrity is one of the most important factors influencing the performance of the produced components. Hence, this research concentrated on the machined surface integrity induced by the multi-axis milling operation with different inclination angle combinations. In this research work, the cutting conditions of the conventional or up-milling process with tool orientations were divided into eight different types, and the machining characteristics corresponding to different cutting strategies were discussed. The varying conditions of surface topography, texture and other machining features induced in machining process which corresponds to different inclination angle combinations were analyzed by geometrical analysis, and the surface roughness and linear profile along specific directions on the machined surface were also investigated. There is a special corresponding relationship between the rotation angle and tool tilt and lead angles. Better surface roughness could be achieved when rotation angles are 0° (positive lead), 60° (combination of positive tilt and positive lead), 90° (positive tilt) and 330° (combination of negative tilt and positive lead). Then, the samples used for study of the metamorphic layer were produced by lapping and polishing process, and the macro hardness (HL) and micro-hardness (HV) of the top machined surface were investigated. According to the measured results of both Leeb hardness and micro-hardness, higher surface hardness could be obtained under rotation angles of 60° (combination of positive tilt and positive lead), 120° (combination of positive tilt and negative lead) and 210° (negative tilt and negative lead). Moreover, the variations of the micro-hardness along the depth direction of the samples were studied. Finally, discussions on the machined surface residual stresses in both feed and cross-feed direction were carried out. Compressive surface residual stress in both feed and cross-feed direction could be generated when rotation angles are 210° (combination of negative tilt angle with smaller value and negative lead angle with larger value) and 330° (combination of negative tilt angle with smaller value and positive lead angle with larger value). Generally, the evaluation indicators of surface integrity are not all very satisfying under one special cutting condition with a certain inclination angle combination, and the optimal cutting parameters should be selected based on the specific application requirements. Finally, the optimal tool orientations and related cutting parameters were recommended, and further studies of the related topics were also presented.Keywords
This publication has 27 references indexed in Scilit:
- Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloyProceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2013
- Experimental investigation of magneto rheological damping effect on surface roughness of work piece during end milling processInternational Journal of Precision Engineering and Manufacturing, 2012
- An Initial Study of the Effect of Using Liquid Nitrogen Coolant on the Surface Roughness of Inconel 718 Nickel-Based Alloy in CNC MillingProcedia CIRP, 2012
- Influence of slab milling process parameters on surface integrity of HSLA: a multi-performance characteristics optimizationThe International Journal of Advanced Manufacturing Technology, 2011
- Surface integrity in high speed end milling of titanium alloy Ti–6Al–4VMaterials Science and Technology, 2011
- Surface integrity in material removal processes: Recent advancesCIRP Annals, 2011
- Effects of milling condition on the surface integrity of hot forged steelJournal of the Brazilian Society of Mechanical Sciences and Engineering, 2010
- Optimum damage and surface roughness prediction in end milling glass fibre-reinforced plastics, using neural network and genetic algorithmProceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2009
- Surface integrity of dry machined titanium alloysInternational Journal of Machine Tools and Manufacture, 2009
- Influence of radial and axial runouts on surface roughness in face milling with round insert cutting toolsInternational Journal of Machine Tools and Manufacture, 2004