Recycling of polycarbonate from optical lens manufacturing waste via solvent-targeted recovery and precipitation
Authors:
- Charles GrangerCGCharles Granger
- Vikas ParakhVPVikas Parakh
- Panzheng ZhouPZPanzheng Zhou
- Ezra Bar-ZivEBEzra Bar-Ziv
- Styliana AvraamidouSAStyliana Avraamidou
- Reid C. Van LehnRLReid C. Van Lehn
- George W. HuberGHGeorge W. Huber
Preprint
- 28 May 2026
- preprint
- Published by Elsevier in SSRN Electronic Journal
Abstract
Polycarbonate (PC) is widely used in optical lenses, and lens manufacturing generates a heterogeneous waste stream known as swarf that also contains polyurethanes, thermoset resins, coatings, and process debris and is currently unrecyclable. In this study, solvent‑targeted recovery and precipitation (STRAP™) is evaluated as a selective dissolution approach to recover PC from optical lens swarf under mild conditions (<70 °C, ambient pressure). Solvent selection was guided by COSMO‑RS modeling to identify candidates capable of dissolving PC while minimizing dissolution of urethane‑based resins. Among the solvents tested, tetrahydrofuran (THF) dissolved the most swarf (62 wt%), outperforming toluene (52 wt%) and xylenes (44 wt%). Spectroscopic (FTIR), thermal (TGA, DSC), and chromatographic (GPC) analyses indicate that the THF‑recovered fraction consists of PC, with no detectable contamination from other polymers. A reduction in glass transition temperature (112.8 °C versus 142.1 °C for virgin PC) and minor early mass loss in TGA suggest slight degradation during processing (either before or during STRAP) and retention of residual solvent, highlighting the need for improved solvent removal strategies to restore material properties.A technoeconomic analysis of a small-scale STRAP facility (2,000–10,000 t*yr⁻¹) indicates that, under favorable assumptions for feedstock logistics, solvent-based PC recovery from swarf can be economically viable; specifically, a 5,000 t*yr⁻¹ plant selling recycled PC at $2.50 kg⁻¹ achieves a 15% IRR. Life cycle assessment shows an ≈80% reduction in cradle-to-gate greenhouse gas emissions versus virgin PC, with electricity dominating impacts. Further development is needed to address solvent management, feedstock variability, and polymer performance at scale.Keywords
This publication has 35 references indexed in Scilit:
- A review of recent advances in fabrication of optical Fresnel lensesJournal of Manufacturing Processes, 2021
- Reducing Antisolvent Use in the STRAP Process by Enabling a Temperature‐Controlled Polymer Dissolution and Precipitation for the Recycling of Multilayer Plastic FilmsChemSusChem, 2021
- Computational Approach for Rapidly Predicting Temperature‐Dependent Polymer Solubilities Using Molecular‐Scale ModelsChemSusChem, 2021
- Value of modular production concepts in future chemical industry production networksEuropean Journal of Operational Research, 2019
- Modular manufacturing processes: Status, challenges, and opportunitiesAIChE Journal, 2017
- Effect of reprocessing and accelerated ageing on thermal and mechanical polycarbonate propertiesJournal of Materials Processing Technology, 2010
- Fracture behaviour of thermosetting polymers for ophthalmic lensesEngineering Failure Analysis, 2010
- Thermal studies on unirradiated and γ-irradiated polymer of allyl diglycol carbonateThermochimica Acta, 1995
- FT-IR spectroscopic studies of polyurethanes Part I. Bonding between urethane COC groups and the NH GroupsJournal of Molecular Structure, 1991
- The Diffusion and Sorption of Gases and Vapours in Glassy Polymers1973