Trimethylaluminum and Oxygen Atomic Layer Deposition on Hydroxyl-Free Cu(111)
Open Access
- 9 July 2015
- journal article
- research article
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 7 (30) , 16428-16439
Abstract
Atomic layer deposition (ALD) of alumina using trimethylaluminum (TMA) has technological importance in microelectronics. This process has demonstrated a high potential in applications of protective coatings on Cu surfaces for control of diffusion of Cu in Cu2S films in photovoltaic devices and sintering of Cu-based nanoparticles in liquid phase hydrogenation reactions. With this motivation in mind, the reaction between TMA and oxygen was investigated on Cu(111) and Cu2O/Cu(111) surfaces. TMA did not adsorb on the Cu(111) surface, a result consistent with density functional theory (DFT) calculations predicting that TMA adsorption and decomposition are thermodynamically unfavorable on pure Cu(111). On the other hand, TMA readily adsorbed on the Cu2O/Cu(111) surface at 473 K resulting in the reduction of some surface Cu1+ to metallic copper (Cu0) and the formation of a copper aluminate, most likely CuAlO2. The reaction is limited by the amount of surface oxygen. After the first TMA half-cycle on Cu2O/Cu(111), two-dimensional (2D) islands of the aluminate were observed on the surface by scanning tunneling microscopy (STM). According to DFT calculations, TMA decomposed completely on Cu2O/Cu(111). High-resolution electron energy loss spectroscopy (HREELS) was used to distinguish between tetrahedrally (Altet) and octahedrally (Aloct) coordinated Al3+ in surface adlayers. TMA dosing produced an aluminum oxide film, which contained more octahedrally coordinated Al3+ (Altet/Aloct HREELS peak area ratio ≈ 0.3) than did dosing O2 (Altet/Aloct HREELS peak area ratio ≈ 0.5). After the first ALD cycle, TMA reacted with both Cu2O and aluminum oxide surfaces in the absence of hydroxyl groups until film closure by the fourth ALD cycle. Then, TMA continued to react with surface Al–O, forming stoichiometric Al2O3. O2 half-cycles at 623 K were more effective for carbon removal than O2 half-cycles at 473 K or water half-cycles at 623 K. The growth rate was approximately 3–4 Å/cycle for TMA+O2 ALD (O2 half-cycles at 623 K). No preferential growth of Al2O3 on the steps of Cu(111) was observed. According to STM, Al2O3 grows homogeneously on Cu(111) terraces.Keywords
Funding Information
- Austrian Science Fund (F4503-N16)
- Basic Energy Sciences
This publication has 56 references indexed in Scilit:
- Atomic Layer Deposition Overcoating: Tuning Catalyst Selectivity for Biomass ConversionAngewandte Chemie International Edition, 2014
- Pore Structure and Bifunctional Catalyst Activity of Overlayers Applied by Atomic Layer Deposition on Copper NanoparticlesACS Catalysis, 2014
- Stabilization of Copper Catalysts for Liquid‐Phase Reactions by Atomic Layer DepositionAngewandte Chemie International Edition, 2013
- Microstructure Evolution of Copper in Nanoscale Interconnect Features2013
- Stabilizing Cu2S for Photovoltaics One Atomic Layer at a TimeACS Applied Materials & Interfaces, 2013
- Improvement of oxidation resistance of copper by atomic layer depositionApplied Surface Science, 2012
- Al2O3 and TiO2 Atomic Layer Deposition on Copper for Water Corrosion ResistanceACS Applied Materials & Interfaces, 2011
- First-Principles Study on the Origin of the Different Selectivities for Methanol Steam Reforming on Cu(111) and Pd(111)The Journal of Physical Chemistry C, 2010
- On the Mechanism of Low-Temperature Water Gas Shift Reaction on CopperJournal of the American Chemical Society, 2008
- Fabrication and characterization of sub-quarter-micron MOSFETs with a copper gate electrodeIEEE Electron Device Letters, 1999