Iron Pyrite Thin Films Synthesized from an Fe(acac)3Ink
Authors:
- Moritz LimpinselMLMoritz Limpinsel
- Yu LiuYLYu Liu
- Nima FarhiNFNima Farhi
- Amanda WeberAWAmanda Weber
- Yanning ZhangYZYanning Zhang
- Nicholas BerryNBNicholas Berry
- Yon Joo KwonYKYon Joo Kwon
- John C. HemmingerJHJohn C. Hemminger
- Ruqian WuRWRuqian Wu
- Matt LawMLMatt Law
- 11 February 2013
- journal article
- research article
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 135 (11) , 4412-4424
Abstract
Iron pyrite (cubic FeS2) is a promising candidate absorber material for earth-abundant thin-film solar cells. Here, we report on phase-pure, large-grain, and uniform polycrystalline pyrite films that are fabricated by solution-phase deposition of an iron(III) acetylacetonate molecular ink followed by sequential annealing in air, H2S, and sulfur gas at temperatures up to 550 °C. Phase and elemental compositions of the films are characterized by conventional and synchrotron X-ray diffraction, Raman spectroscopy, Auger electron spectroscopy, secondary ion mass spectrometry, and X-ray photoelectron spectroscopy (XPS). These solution-deposited films have more oxygen and alkalis, less carbon and hydrogen, and smaller optical band gaps (Eg = 0.87 ± 0.05 eV) than similar films made by chemical vapor deposition. XPS is used to assess the chemical composition of the film surface before and after exposure to air and immersion in water to remove surface contaminants. Optical measurements of films rich in marcasite (orthorhombic FeS2) show that marcasite has a band gap at least as large as pyrite and that the two polymorphs share similar absorptivity spectra, in excellent agreement with density functional theory models. Regardless of the marcasite and elemental impurity contents, all films show p-type, weakly activated transport with curved Arrhenius plots, a room-temperature resistivity of ∼1 Ω cm, and a hole mobility that is too small to measure by Hall effect. This universal electrical behavior strongly suggests that a common defect or a hole-rich surface layer governs the electrical properties of most FeS2 thin films.Keywords
This publication has 80 references indexed in Scilit:
- Atmospheric‐Pressure Chemical Vapor Deposition of Iron Pyrite Thin FilmsAdvanced Energy Materials, 2012
- Low-Cost Inorganic Solar Cells: From Ink To Printed DeviceChemical Reviews, 2010
- Characterization of FeS2-pyrite thin films synthesized by sulphuration of amorphous iron oxide films pre-deposited by spray pyrolysisMaterials Characterization, 2005
- Pyrite (FeS2) thin films prepared by spray method using FeSO4 and (NH4)2SxSolar Energy Materials and Solar Cells, 2003
- Iron disulfide for solar energy conversionSolar Energy Materials and Solar Cells, 1993
- Photovoltaic output limitation of n-FeS2 (pyrite) Schottky barriers: A temperature-dependent characterizationJournal of Applied Physics, 1992
- Photoactive thin film semiconducting iron pyrite prepared by sulfurization of iron oxidesSolar Energy Materials, 1990
- Formation of semiconducting iron pyrite by spray pyrolysisSolar Energy Materials, 1989
- Interband transitions of chemically deposited pyrite FeS2 films in the fundamental absorption region between 1 and 3.8 eVPhysica Status Solidi (a), 1986
- Photoelectrochemistry of Highly Quantum Efficient Single‐Crystalline n ‐ FeS2 (Pyrite)Journal of the Electrochemical Society, 1986