Influence of Cu coating thickness on the microstructural evolution and superconducting properties of IMD-MgB2 wires
Authors:
- K. SonmezKSK. Sonmez
- Serap SafranSSSerap Safran
- A. GencerAGA. Gencer
- Chen GuoCGChen Guo
- F. Al-MokdadFAF. Al-Mokdad
- F. ErvuzFEF. Ervuz
- H. KoralayHKH. Koralay
- Y. OznalYOY. Oznal
- S. SalahiSSS. Salahi
- Ayten SeçkinASAyten Seçkin
- S. C. TaskinSTS. C. Taskin
- Dongliang WangDWDongliang Wang
Preprint
- 4 February 2026
- preprint
- Published by Elsevier in SSRN Electronic Journal
Abstract
In this study, the effect of nanoscale Copper (Cu) coating thickness on the phase formation kinetics, microstructural homogeneity, and superconducting properties of Internal Mg Diffusion (IMD) processed MgB2 wires was systematically investigated. Central Mg rods were coated with Cu layers ranging from 200 nm to 800 nm to act as an in-situ sintering activator. Differential Thermal Analysis (DTA) revealed that the Cu coating lowers the reaction onset temperature significantly by forming a Mg-Cu eutectic liquid phase, facilitating MgB2 formation even at low temperatures (575 °C). Building on our recent findings on the beneficial effects of thin (200 nm) Cu coatings, we demonstrate that increasing the activator thickness has a profound impact on phase uniformity. Resistivity measurements (R-T) show that while 200 nm coated wires exhibited broad transitions (ΔT» 1.8 K) at low sintering temperatures due to less pronounced reaction kinetics, wires with 800 nm coatings displayed remarkably sharp transitions (ΔT» 1.0 K) and dense microstructures, indicating superior phase homogeneity driven by enhanced Mg diffusion. However, transport critical current density (Jc) measurements revealed a competing mechanism: while thicker Cu coatings improve intra-granular connectivity, they also lead to the segregation of Cu-based impurities (e.g., MgCu2) at grain boundaries, which suppresses inter-granular current flow. Consequently, an optimal balance was achieved for the 200 nm Cu-coated wire sintered at 625 °C, which exhibited the highest Jc performance among the samples studied in this research. These results provide a comprehensive guideline for interface engineering in IMD-MgB2 wires, demonstrating that Cu-activation is a viable route for fabricating high-performance superconductors, making MgB2 more competitive to the other prospective superconductors at lower cost for potential applications.Keywords
This publication has 21 references indexed in Scilit:
- Interfacial reactions and critical current density of Cu-sheathed Cu-doped MgB2 wire with Ti diffusion barrierJournal of Alloys and Compounds, 2023
- Influence of annealing temperature and isostatic pressure on microstructure and superconducting properties of isotopic Mg11B2 wires fabricated by internal Mg diffusion methodJournal of Alloys and Compounds, 2022
- The kinetics mechanism of MgB2 layer formation within MgB2 superconducting wire fabricated using improved internal Mg diffusion processJournal of Alloys and Compounds, 2017
- Kinetic analysis of MgB2 layer formation in advanced internal magnesium infiltration (AIMI) processed MgB2 wiresActa Materialia, 2015
- Microstructure of MgB2 superconducting wire prepared by internal magnesium diffusion processJournal of Alloys and Compounds, 2015
- Study of MgB2 phase formation by using XRD, SEM, thermal and magnetic measurementsJournal of Alloys and Compounds, 2013
- Tailored Materials for High‐Performance MgB2 WireAdvanced Materials, 2011
- The structure of liquid Mg–Cu binary alloysJournal of Non-Crystalline Solids, 2010
- Enhanced critical current properties of in situ processed MgB2 wires using milled boron powder and low temperature solid-state reactionJournal of Alloys and Compounds, 2010
- The mechanism of accelerated phase formation of MgB2 by Cu-doping during low-temperature sinteringMaterials Research Bulletin, 2009