Friction and wear behaviours of some industrial polyamides against different polymer counterparts under dry conditions
Authors:
- 20 June 2008
- journal article
- research article
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 60 (4) , 195-200
Abstract
Purpose: The present study aims to find out the best polymer/polymer pair in electrical insulating applications. Moreover, the effects of different polymer counterpart and applied load on the friction and wear behaviour of PA 46 + 30%GFR and unfilled PA 66 thermoplastic polymers are to be studied.Design/methodology/approach: Friction and wear tests vs PA 46 + 30%GFR and PPS + 30%GFR polymer composites were carried out on a pin‐on‐disc arrangement and at a dry sliding conditions. Tribological tests were performed at room temperature under 20, 40 and 60 N loads and at 0.5 m/s sliding speed.Findings: The results showed that, the coefficient of friction decreases with the increasing of load (up to 40 N) for PA 46 + 30%GFR composite and polyamide (PA) 66 polymer used in this study. However, above 40 N applied load the coefficient of friction increases. The specific wear rate for PA 46 + 30%GFR and PA 66 against PPS + 30%GFR polymer composite counterpart are about in the order of 10−13 m2/N while the specific wear rate for PA 46 + 30%GFR and PA 66 against PA 46 + 30%GFR polymer composite counterpart are in the order of 10−14 m2/N. For PA 46 + 30%GFR composite and unfilled PA 66 polymers tested the specific wear rate values increased with the increment of load. The highest specific wear rate is for unfilled PA 66 against PPS + 30%GFR with a value of 2.81 × 10−13 m2/N followed by PA 66 against PA 46 + 30%GFR with a value of 2.26 × 10−13 m2/N. The lowest wear rate is PA 46 + 30%GFR polymer composite against PA 46 + 30%GFR polymer composite counterpart with a value of 3.19 × 10−14 m2/N. The average specific wear rates for unfilled PA 66 against PA 46 + 30%GFR is 80 times higher than PA 46 + 30%GFR wear rate while specific wear rates for unfilled PA 66 against PPS + 30%GFR is 100 times higher than that of PA 46 + 30%GFR wear rate. From point view of tribological performance, PA 46 + 30%GFR is a more suitable engineering thermoplastic composite materials for electrical contact breaker applications.Research limitations/implications: In the present work, tribological tests were performed only at room temperature under three different loads and a sliding speed. This is the limitation of the work.Practical implications: This work is easily used for industrial polyamides to check their tribological behaviours.Originality/value: This is an original and experimental study and it will be useful both for academicians and for industrial sides.Keywords
This publication has 24 references indexed in Scilit:
- On the sliding wear of nanoparticle filled polyamide 66 compositesComposites Science and Technology, 2006
- Tribological behaviours of PA/UHMWPE blend under dry and lubricating conditionWear, 2006
- The effect of different metallic counterface materials and different surface treatments on the wear and friction of polyamide 66 and its composite in rolling–sliding contactWear, 2003
- Friction and wear behaviour of unfilled engineering thermoplasticsMaterials & Design (1980-2015), 2003
- Friction and wear of water lubricated PEEK and PPS sliding contactsWear, 2002
- Tribological studies of polyamide 6 and high-density polyethylene blends filled with PTFE and copper oxide and reinforced with short glass fibersWear, 2002
- FRICTION AND WEAR BEHAVIORS OF TOUGHENED POLYOXYMETHYLENE BLEND UNDER WATER LUBRICATIONPolymer-Plastics Technology and Engineering, 2000
- Studies on the tribological behavior and transfer film–counterface bond strength for polyphenylene sulfide filled with nanoscale alumina particlesWear, 2000
- On the tribological behaviour of selected, injection moulded thermoplastic compositesComposites Part A: Applied Science and Manufacturing, 1998
- The role of copper compounds as fillers in transfer film formation and wear of nylonWear, 1992