Preparation of a Sustainable Shape-Stabilized Phase Change Material for Thermal Energy Storage Based on Mg2+-Doped CaCO3/PEG Composites
Authors:
- Hasan ZahirHZHasan Zahir
- Mohammad Mominur RahmanMohammad Mominur Rahman
- Salem K. S. BasamadSBSalem K. S. Basamad
- Khaled Own MohaisenKMKhaled Own Mohaisen
- Kashif IrshadKIKashif Irshad
- Mohammad Mizanur RahmanMRMohammad Mizanur Rahman
- Abdul AzizAbdul Aziz
- Amjad AliAmjad Ali
- Mohammad M. HossainMohammad M. Hossain
Open Access
- 22 June 2021
- journal article
- research article
- Published by MDPI AG in Nanomaterials
- Vol. 11 (7) , 1639
Abstract
The properties of polyethylene glycol-6000 (PEG)/MgCaCO3, a low-cost shape-selective phase change material (ss-PCM), make it highly suitable for solar thermal applications. Nanosized porous MgO-doped CaCO3 with Mg molar concentrations of 5%, 10%, and 15% were synthesized using a hydrothermal technique. The prepared MgO-CaCO3 matrices were then impregnated with PEG to obtain PEG/MgCaCO3 as an ss-PCM. Samples identified as PEG-5MgCaCO3 (P-5-MCC), PEG-10MgCaCO3 (P-10-MCC), and PEG-15MgCaCO3 (P-15-MCC) were prepared and studied. Interestingly, P-10-MCC has the smallest particle size together with a good porous structure compared to the other two materials. The results of thermogravimetric analyses and differential scanning calorimetry indicate that the small particle size and porous structure facilitate the impregnation of approximately 69% of the PEG into the 10-MCC matrix. The latent heat and energy storage efficiency of PEG in the P-10-MCC sample are 152.5 J/g and 96.48%, respectively, which are significantly higher than those of comparable materials. Furthermore, in addition to the improvement of the thermal conductivity of the P-10-MCC, its supercooling is also reduced to some extent. The combined mesoporous and macro-porous structure of P-10-MCC is critical to retaining a large amount of PEG within the matrix, resulting in a high latent heat in the operating temperature range of 35–57 °C. The P-10MCC sample also demonstrates a high energy storage capacity (98.59%), high thermal energy storage/release rates, and exceptional shape-stabilized PCM properties.Keywords
Funding Information
- King Fahad University of petroleum & Minerals (DF191056)
This publication has 54 references indexed in Scilit:
- Facile preparation of hierarchically porous carbon using diatomite as both template and catalyst and methylene blue adsorption of carbon productsJournal of Colloid and Interface Science, 2012
- Electro- and Photodriven Phase Change Composites Based on Wax-Infiltrated Carbon Nanotube SpongesACS Nano, 2012
- Form-stable phase change materials for thermal energy storageRenewable and Sustainable Energy Reviews, 2012
- Polyethylene glycol (PEG)/diatomite composite as a novel form-stable phase change material for thermal energy storageSolar Energy Materials and Solar Cells, 2011
- Effect of polyethylene glycol on phase and morphology of calcium carbonateJournal of Applied Polymer Science, 2010
- Macroscaled mesoporous calcium carbonate tetragonal prisms: top-down solid-phase fabrication and applications of phase-change material support matricesCrystEngComm, 2010
- Identification and spectra–structure determination of soil minerals: Raman study supported by IR spectroscopy and X‐ray powder diffractionJournal of Raman Spectroscopy, 2009
- Numerical study for enhancing the thermal conductivity of phase change material (PCM) storage using high thermal conductivity porous matrixEnergy Conversion and Management, 2005
- A review on phase change energy storage: materials and applicationsEnergy Conversion and Management, 2004
- Influence of the Mg-content on ESR-signals in synthetic calcium carbonateInternational Journal of Radiation Applications and Instrumentation. Part A. Applied Radiation and Isotopes, 1989