Time-resolved ion mass spectrometry analysis reveal high Bi2+ and Bi3+ ion fluxes during high-power impulse magnetron sputtering of Bi target
Open Access
- 25 November 2025
- journal article
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (6)
Abstract
Time-resolved ion mass spectrometry was used to investigate the ion fluxes present during high-power impulse magnetron sputtering of a Bi target in an argon atmosphere. The study focuses on the temporal evolution of singly, doubly, and triply charged Bi ions (Bi+, Bi2+, and Bi3+) under two different discharge conditions with varying peak target current densities (JT) and pulse frequencies (f). The results show that Bi2+ and Bi3+ ions dominate the ion population in the postpulse plasma, with Bi2+ exhibiting the highest flux across both discharge conditions. Interestingly, the lower peak target current density JT = 0.07 A/cm2 (f = 2000 Hz) results in higher total ion fluxes and longer ion persistence compared to those detected with JT of 0.18 A/cm2 (f = 700 Hz). Severe Ar gas rarefaction, enhanced by the high sputter yield and large mass of Bi, strongly influences the ion energy distribution functions. Both Bi2+ and Bi3+ exhibit a dominant low-energy peak (0–10 eV) from ions emitted in preceding pulses, together with broad Sigmund–Thompson-like tails extending up to ∼25–30 eV due to ions generated during the ongoing discharge. At JT = 0.07 A/cm2 (f = 2000Hz), the short off-time (470 μs) is insufficient for full ion thermalization, resulting in residual high-energy ions persisting into the early afterglow. In contrast, at 0.18 A/cm2 (f = 700 Hz), the longer off-time (∼1.4 ms) enables complete thermalization. As a result, the mean ion charge state remains above 2.0 in both cases but is slightly higher at lower JT (2.17–2.28 vs 2.07–2.15). These findings provide practical guidelines for substrate biasing: bias should be applied after ∼90 μs to minimize Ar implantation and optimized at reduced amplitudes (2–3 times lower than for Ta or W) to take advantage of the high Bi charge states without inducing excessive ion damage.Keywords
This publication has 88 references indexed in Scilit:
- Advanced film/substrate interface engineering for adhesion improvement employing time- and energy-controlled metal ion irradiationApplied Surface Science, 2024
- Superhard oxidation-resistant Ti1-xAlxBy thin films grown by hybrid HiPIMS/DCMS co-sputtering diboride targets without external substrate heatingMaterials & Design, 2024
- Energy-efficient physical vapor deposition of dense and hard Ti-Al-W-N coatings deposited under industrial conditionsMaterials & Design, 2023
- Role of energetic ions in the growth of fcc and ω crystalline phases in Ti films deposited by HiPIMSApplied Surface Science, 2021
- Mass spectrometry analyzes to highlight differences between short and long HiPIMS dischargesApplied Surface Science, 2016
- Optimizing HiPIMS pressure for deposition of high-k (k = 18.3) amorphous HfO2Applied Surface Science, 2016
- The formation of ordered bismuth nanowire arrays within mesoporous silica templatesMaterials Chemistry and Physics, 2007
- Time-Resolved Ionisation Studies of the High Power Impulse Magnetron Discharge in Mixed Argon and Nitrogen AtmospherePlasma Processes and Polymers, 2007
- Structure and electrical transport properties of bismuth thin films prepared by RF magnetron sputteringApplied Surface Science, 2006
- Substrate dependence of large ordinary magnetoresistance in sputtered Bi filmsJournal of Magnetism and Magnetic Materials, 2004