Investigation of the Hot Deformation Behavior and Mechanism of a Medium-Entropy CoCr0.4NiSi0.3 Alloy
Open Access
Abstract
The CoCrNi-based medium-entropy alloys (MEA) have been extensively investigated due to their exceptional mechanical properties at both room and cryogenic temperatures. To investigate the hot deformation behavior and the recrystallization mechanism of the CoCr0.4NiSi0.3 medium-entropy alloy, a series of deformation tests was conducted using the MMS-100 thermal simulation tester, with deformation conditions of 0.001–1 s−1/850–1150 °C. During the hot deformation process, the flow stress initially increases up to its peak value before gradually decreasing towards a steady state level. Higher flow stress levels are observed with increasing strain rate and decreasing deformation temperature. The estimated activation energy for hot deformation of this alloy is approximately 423.6602 kJ/mol. The Arrhenius-type constitutive equation is utilized to establish a modified model while incorporating power dissipation theory and the instability criterion of a dynamic material model to construct power dissipation maps and instability maps. By superimposing these maps, hot processing maps with strains of 0.4, 0.5, and 0.7 are derived. In this investigation, it is observed that regions of instability exclusively occur when the true strain exceeds 0.4. These regions of instability on the hot processing map align well with experimental findings. The suitable range of parameters for hot-working decreases as the true strain increases. The microstructure was analyzed using electron backscatter diffraction and transmission electron microscopy (TEM) techniques. The volume fraction of dynamic recrystallization (DRX) decreases with increasing strain rate but diminishes with rising temperature. The TEM characterization elucidated the mechanism of DRX in this MEA. The presence of the long-period stacking ordered (LPSO) phase was observed in both the face-centered cubic matrix and hexagonal close-packed recrystallized grains under different deformation conditions. The LPSO phase originates from the matrix at a low strain rate, whereas it is generated during recrystallization at a high strain rate. The observed increase in flow stress of the as-cast MEA is primarily attributed to the synergistic effects arising from the interaction of the dislocation with twins and the second phase. The onset of instability is effectively suppressed within a limited range through the formation of coherent second phases such as L12, LPSO, and superlattice structures resulting from phase transitions. These second phases serve as nucleation sites for recrystallization and contribute to the strengthening of dispersion. Furthermore, their interaction with dislocations and twins significantly influences both flow stress behavior and recrystallization kinetics under hot deformation. These findings not only deepen our understanding of the underlying deformation mechanisms governing MEA but also offer valuable insights for designing CoCrNi-based alloys with improved mechanical properties at elevated temperatures.Keywords
Funding Information
- The Education Department of Liaoning Province of China (LJKMZ20220592)
This publication has 55 references indexed in Scilit:
- Microstructures and mechanical properties of the Mg–8Gd–4Y–Nd–Zn–3Si (wt%) alloyMaterials Science and Engineering: A, 2013
- Modelling radiation-induced phase changes in binary FeCu and ternary FeCuNi alloys using an artificial intelligence-based atomistic kinetic Monte Carlo approachNuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms, 2009
- Nanostructured High‐Entropy Alloys with Multiple Principal Elements: Novel Alloy Design Concepts and OutcomesAdvanced Engineering Materials, 2004
- Necklace formation during dynamic recrystallization: mechanisms and impact on flow behaviorActa Materialia, 1998
- Processing maps for hot working of titanium alloysMaterials Science and Engineering: A, 1998
- Hot working characteristics of nimonic 75, 80A and 90 superalloys: a comparison using processing mapsJournal of Materials Processing Technology, 1995
- Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242Metallurgical Transactions A, 1984
- Development of a Processing Map for Use in Warm-Forming and Hot-Forming ProcessesMetallurgical Transactions A, 1981
- Long period stacking order in close packed structures of metalsJournal of Physics and Chemistry of Solids, 1967
- On the mechanism of hot deformationActa Metallurgica, 1966