Characteristics and Influencing Factors of Multi-Scale Pore Structure Heterogeneity of Lacustrine Shale in the Gaoyou Sag, Eastern China
Open Access
Abstract
The success of shale oil exploration and production is highly dependent on the heterogeneous nature of the reservoir pore structure. Despite this, there remains limited research on the heterogeneity characteristics of pores at different scales in lacustrine shale oil reservoirs and the factors that impact them. This study aims to quantitatively characterize the multi-scale pore heterogeneity differences of the lacustrine shale found in the Funing Formation in Gaoyou Sag. Additionally, the study seeks to clarify the impact of the total organic carbon (TOC) and lithofacies type on pore structure heterogeneity. To achieve this, nitrogen adsorption, scanning electronic microscope (SEM), mercury intrusion porosimetry (MIP), and other experimental means were adopted in combination with the fractal dimension model of FHH and capillary. The results show that the predominant lithofacies of the Funing Formation shale samples are mixed shale (MS) and siliceous shale (SS), with a limited presence of calcareous shale (CS). The micro-pores of lacustrine shale are dominated by inorganic mineral pores and fewer organic pores. Intragranular pores and clay mineral pores are two types of inorganic mineral pores that are widely found. Small pores (pore diameter < 50 nm) make up 89% of the pore volume (PV) and 99% of the specific surface area (SSA). The fractal dimensions D1, D2, and D3 were calculated to characterize the roughness of the pore surface, the structural complexity of small pores, and the structural complexity of large pores (pore diameter > 50 nm), respectively. The increase in the total organic carbon (TOC) resulted in a decrease in the D1, D2, PV, and SSA, while connectivity showed a slight improvement. The fractal dimension of shale across all lithofacies followed the pattern: D3 > D2 > D1. The pore structure is more complex than the pore surface, and the large pores showed a greater heterogeneity than the small pores. Among the three lithofacies, CS had the largest PV, SSA, D1, and D2, indicating the development of a more complex pore structure network. This expands the space required for shale oil occurrence. However, the connectivity of the CS lithofacies is the lowest among the three, which hinders shale oil production. Although the PV of SS is slightly lower than that of CS, its average pore diameter (AVE PD) and connectivity are significantly advantageous, making SS an ideal shale reservoir. This study provides an important reference for the reservoir evaluation required to better develop lacustrine shale oil around the world.Keywords
Funding Information
- National Natural Science Foundation of China (42272137, 41872135, 42072151)
This publication has 50 references indexed in Scilit:
- Development of organic porosity in the Woodford Shale with increasing thermal maturityInternational Journal of Coal Geology, 2012
- CO2 storage capacity assessment of deep saline aquifers in the Subei Basin, East ChinaInternational Journal of Greenhouse Gas Control, 2012
- Spectrum of pore types and networks in mudrocks and a descriptive classification for matrix-related mudrock poresAAPG Bulletin, 2012
- Clay mineral transformation as a major source for authigenic quartz in thermo-mature gas shaleApplied Clay Science, 2012
- Porous structure and sorption properties of nitrogen-containing activated carbonFuel, 2010
- Smectite-illite-muscovite transformations, quartz dissolution, and Silica release in shalesClays and Clay Minerals, 2008
- Fractal characterization of adsorption-pores of coals from North China: An investigation on CH4 adsorption capacity of coalsInternational Journal of Coal Geology, 2008
- An investigation of fractal characteristics of mesoporous carbon electrodes with various pore structuresElectrochimica Acta, 2004
- Fractal Analysis and Surface Roughness of Nonporous Carbon Fibers and Carbon BlacksLangmuir, 1994
- Reporting physisorption data for gas/solid systems with special reference to the determination of surface area and porosity (Recommendations 1984)Pure and Applied Chemistry, 1985