Effect of the heat treatment time on microstructure and fracture toughness of laser-clad TiB2-TiC pseudoeutectic reinforced TiNi/Ti2Ni intermetallic matrix composite coating
Authors:
- 29 April 2016
- journal article
- research article
- Published by EDP Sciences in Metallurgical Research & Technology
- Vol. 113 (3) , 304
Abstract
A TiNi/Ti2Ni intermetallic matrix composite coating reinforced by TiB2 and TiC pseudoeutectic structures was prepared on a Ti6Al4V substrate by laser cladding using Ni based and B4C powder as the cladding material. The coatings were heat treated for different durations (2, 4, and 6 h) at 600 °C. The microstructures of the heat-treated and untreated coatings were then characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectrometry. The microhardness and fracture toughness of the coatings were also evaluated. Results reveal that the coating without heat treatment was mainly composed of TiNi/Ti2Ni as the matrix and TiB2/TiC as the reinforcements. TiB2 and TiC belong to the pseudoeutectic microstructures, in which a large number of fine columnar/spherical TiC particles are uniformly distributed within the coarse willow-shaped TiB2 particles. Many fine needle-shaped Ti2Ni particles were precipitated within the initial TiNi grains in the coatings with heat treatment. With the extension in heat treatment time, more Ti2Ni particles were precipitated. Furthermore, the average microhardness of the coatings was decreased: 941.3 HV0.2 (0 h) 933.2 HV0.2 (2 h), 903.8 HV0.2 (4 h), 890.4 HV0.2 (6 h), whereas the average fracture toughness presented an opposite trend: 4.18 MPa.m1/2 (0 h), 4.26 MPa.m1/2 (2 h), 4.37 MPa.m1/2 (4 h), 4.90 MPa.m1/2 (6 h).Keywords
This publication has 14 references indexed in Scilit:
- Effects of post-heat treatment on microstructure and properties of laser cladded composite coatings on titanium alloy substrateOptics & Laser Technology, 2015
- Effects of high temperature treatment on microstructure and mechanical properties of laser-clad NiCrBSi/WC coatings on titanium alloy substrateMaterials Characterization, 2014
- Critical assessment and experimental investigation of Co–Ni–Ti phase equilibriaCalphad, 2014
- Effect of Y2O3 on the sliding wear resistance of TiB/TiC-reinforced composite coatings fabricated by laser claddingWear, 2014
- Microstructure and wear resistance of laser clad TiB–TiC/TiNi–Ti2Ni intermetallic coating on titanium alloyTransactions of Nonferrous Metals Society of China, 2012
- Evaluation of modulus of elasticity, nano-hardness and fracture toughness of TiB2–TiC–Al2O3 composite coating developed by SHS and laser claddingMaterials Science and Engineering: A, 2011
- Effect of yttrium on microstructure and mechanical properties of laser clad coatings reinforced by in situ synthesized TiB and TiCJournal of Rare Earths, 2011
- Sliding wear resistance of TiCp reinforced titanium composite coating produced by laser claddingSurface and Coatings Technology, 2010
- A critical assessment and thermodynamic calculation of the boron-carbon-titanium (B-C-Ti) ternary systemJournal of Phase Equilibria and Diffusion, 1995
- Quasi-static solid particle damage in brittle solids—I. Observations analysis and implicationsActa Metallurgica, 1976