Effect of Multistep Processing Technique on the Formation of Micro‐defects and Residual Stresses in Zirconia Dental Restorations
Authors:
- 7 October 2013
- journal article
- research article
- Published by Wiley in Journal of Prosthodontics
- Vol. 23 (3) , 206-212
Abstract
Purpose: The clinical failures of zirconia dental restorations are often caused by extrinsic artifacts introduced by processing. The aim of this study was to investigate the micro‐defects and residual stresses generated during the multistep process of zirconia dental restorations.Materials and Methods: Thermal spray granulated 3Y‐TZP powders were dry pressed by two tools exhibiting distinctly different Young's moduli, cold isostatic pressed (CIP‐ed), and pressure‐less fully sintered. The green bodies pressed by a stiff tool were treated with different procedures: direct milling (green milling) followed by fully sintering; half‐sintering and milling (raw milling) with or without fully sintering; and fully sintering followed by grinding. The fully sintered 3Y‐TZP crowns were clinically adjusted using both a diamond bur and SiC bur, respectively. Phase composition and microstructure of the pressed, milled, and ground surfaces were studied by XRD and SEM.Results: Tetragonal phase was the main phase of all detected 3Y‐TZP specimens. Excessive residual stresses introduced by raw milling and grinding were confirmed by a strained T (111) peak, monoclinic phase, and obviously changed I(002)t/I(200)t ratio. The residual stresses would form a compressive stress layer, while it was too shallow to inhibit crack propagation even for ground specimens. Large voids with high‐coordination numbers were the common packing micro‐defects. Once formed, they were barely healed by CIP‐ing and sintering. A stiff pressing tool was confirmed to be useful for reducing the surface packing voids. Milling removed the surface voids, but was no help for the interior ones. Raw milling introduced more serious chippings, most originating from the existing packing voids, than green milling due to its brittle failure and was less recommended for production. Grinding dense 3Y‐TZP caused surface grain refinement and much more severe micro‐defects, especially when clinical adjustment was applied by diamond bur compared to SiC bur.Conclusions: Micro‐defects and residual stresses are introduced and accumulated through the entire production chain and determine the final microstructure of zirconia dental restorations. Several procedural improvements are offered and expected to reduce processing micro‐defects.Keywords
Funding Information
- China Scholarship Council
- Swedish Research Council through the Berzelii Center EXSELENT
This publication has 24 references indexed in Scilit:
- Damage and Reliability of Y-TZP after Cementation Surface TreatmentJournal of Dental Research, 2010
- A 3-year retrospective and clinical follow-up study of zirconia single crowns performed in a private practiceJournal of Dentistry, 2009
- Strength influencing variables on CAD/CAM zirconia frameworksDental Materials, 2008
- Compaction and Pressureless Sintering of Zirconia NanoparticlesJournal of the American Ceramic Society, 2007
- The influence of surface modification techniques on the performance of a Y-TZP dental ceramicJournal of Dentistry, 2006
- Influence of pore structure inhomogeneities in green compacts on strength and reliability of Y-TZPJournal of the European Ceramic Society, 1990
- Prevention of Low‐Temperature Surface Transformation by Surface Recrystallization in Yttria‐Doped Tetragonal ZirconiaJournal of the American Ceramic Society, 1989
- Strength and Fracture Toughness of Isostatically Hot‐Pressed Composites of Al 2 O 3 and Y 2 O 3 ‐Partially‐Stabilized ZrO 2Journal of the American Ceramic Society, 1985
- Processing‐Related Fracture Origins: I, Observations in Sintered and Isostatically Hot‐Pressed A1 2 O 3 /ZrO 2 CompositesJournal of the American Ceramic Society, 1983
- Ceramic steel?Nature, 1975