Effect of Citrate-Based Bath pH on Properties of Electrodeposited Cu–Zn Coating on an Aluminum Substrate
Authors:
- Rasim ÖzdemirRÖRasim Özdemir
- Ersin ÜnalEÜErsin Ünal
- İsmail KarahanIKİsmail Karahan
Open Access
- 26 July 2024
- journal article
- research article
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 55 (10) , 3937-3955
Abstract
In this study, Cu–Zn alloys were deposited in citrate-based electrolytes on aluminum substrate by electrodeposition method. The effect of bath pH variation on the properties of the obtained Cu–Zn alloy coatings was investigated. The electrochemical behavior of the citrate-based baths and the crystalline structure, surface morphology and elemental content, electrical resistivity and thermal behavior of the alloy coatings were analyzed. According to the results of cyclic voltammetry (CV) analysis, increasing bath pH caused a negative shift in the cathodic deposition potential. In addition, the anodic dissolution peaks first shifted to the positive side with increasing pH and then shifted back to the negative direction. According to the results of XRD analysis, the phase structure of Cu–Zn alloys generally consists of α and β′ phases, but according to differential scanning calorimeter (DSC) analysis, it is possible that there is a γ phase in the structure in addition to these phases. In addition, pH increase (4.5 to 6.5) caused a relative increase in crystal grain size (~14 to ~ 25 nm). The Zn content of Cu–Zn coatings first increased (~pct 15 to ~ pct 55) with pH increase, then followed a horizontal trend (~pct 55 to ~ pct 59) with further pH increase and then exhibited a slight decreasing trend (~pct 59 to ~ pct 52). The pH increase significantly affected the surface morphology of the coatings and denser coatings were obtained with increasing pH. While the electrical resistivity of Cu–Zn coatings first increased (0.0408 to 0.0696 µΩcm for 297 K) with increasing pH, it tended to decrease (0.0696 to 0.0479 µΩcm for 297 K) again at higher pH values. In addition, the electrical resistivity of the coatings increased with increasing measurement temperature. According to DSC analysis of the coatings, endothermic peaks were obtained, possibly representing the transformation from γ to β′ phase. Graphical AbstractKeywords
Funding Information
- Osmaniye Korkut Ata University
This publication has 75 references indexed in Scilit:
- Effect of Electrodeposition Current and Pulse Parameter on Surface Mechanical and Electrochemical Behavior of Ni–W Alloy CoatingsMetallurgical and Materials Transactions A, 2020
- Characterization of Pulse and Direct Current Methods for Electrodeposition of Ni-Co Composite Coatings Reinforced with Nano and Micro ZnO ParticlesMetallurgical and Materials Transactions A, 2019
- A Study on the Effect of Pulse Electrodeposition Parameters on the Morphology of Pure Tin CoatingsMetallurgical and Materials Transactions A, 2014
- Toward Robust Nanogenerators Using Aluminum SubstrateAdvanced Materials, 2012
- Fabrication of Magnetic Layers for Electromagnetic Microactuators2011
- Electrical Resistivity of Thin Metal Films2007
- Microstructure and formability of ZnNi alloy electrodeposited sheet steelMetallurgical and Materials Transactions A, 2000
- Kinetics of copper electrodeposition in citrate electrolytesJournal of Applied Electrochemistry, 1986
- Isothermal decomposition of the ß′ phase in a Cu-Zn-Al alloyJournal of Materials Science, 1984
- A kinetic study of the β to a massive transformation in a Cu-Zn alloyMetallurgical Transactions, 1972