Electrochemical Charge–Discharge Behavior of a Binder‐Free 3D ‐Printed LCNO ‐Derived Multiphase La–Cu–Ni–O Ceramic Electrode
- 23 August 2026
- journal article
- research article
- Published by Wiley in Journal of the Chinese Chemical Society
Abstract
In this study, the electrochemical charge–discharge behavior of a binder‐free, self‐supporting, porous three‐dimensional (3D) LCNO‐derived multiphase La–Cu–Ni–O ceramic electrode (LCNO‐MP) fabricated from a nominal La 2 CuNiO 6 precursor powder (LCNO) was investigated. The sintered electrode derived from this LCNO precursor powder is referred to as the LCNO‐derived multiphase La–Cu–Ni–O ceramic electrode, abbreviated as LCNO‐MP electrode. Structural and morphological analyses (XRD, FE‐SEM, FT‐IR, and BET) confirmed that sintering produced an interconnected porous electrode architecture while preserving a dominant LCNO‐related La–Cu–Ni–O mixed oxide phase accompanied by secondary lanthanum nickel oxide, lanthanum copper oxide, and metallic Ni phases. The electrochemical response of the LCNO‐MP electrode was evaluated in 1.0 M KOH electrolyte using electrochemical impedance spectroscopy (EIS), cathodic polarization, cyclic voltammetry (CV), and galvanostatic charge–discharge (GCD) analyses. EIS results indicated measurable but kinetically limited interfacial charge‐transfer behavior within the standalone porous ceramic electrode. CV analyses revealed faradaic redox features; however, the unusually low b value of 0.243 indicates a highly non‐ideal electrochemical response influenced by polarization, resistive limitations, possible side reactions, and peak‐selection uncertainty rather than a clear diffusion‐controlled hydrogen insertion/extraction mechanism. GCD measurements showed measurable Faradaic charge/discharge behavior; however, the large difference between charge and discharge capacities and the recoverable discharge capacity below 0.20 mAh g −1 indicate poor reversibility, likely due to parasitic hydrogen evolution, irreversible redox processes, polarization losses, and/or other side reactions. Overall, the 22‐cycle GCD test revealed a time‐dependent, non‐stabilized, and poorly reversible electrochemical response.Keywords
Funding Information
- Türkiye Bilimsel ve Teknolojik Araştırma Kurumu (123Z792)
This publication has 50 references indexed in Scilit:
- Tailoring the innovative Lu2CrMnO6 double perovskite nanostructure as an efficient electrode materials for electrochemical hydrogen storage applicationJournal of Energy Storage, 2024
- Achieving new insights on rational design and application of double perovskite Y2CrMnO6 nanostructures as potential materials for electrochemical hydrogen storage performanceJournal of Energy Storage, 2024
- Fabrication of 3D‐printed graphene/polylactic acid and carbon nanofiber/polylactic acid electrodes: New solvent‐free electrochemical activation method for hydrogen evolution reactionsJournal of Applied Polymer Science, 2023
- 3D printing nanocomposites with enhanced mechanical property and excellent electromagnetic wave absorption capability via the introduction of ZIF-derivative modified carbon fibersComposites Part B: Engineering, 2022
- Hydrogen storage in a rare‐earth perovskite‐type oxide La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 for battery applicationsRare Metals, 2018
- Emerging 3D‐Printed Electrochemical Energy Storage Devices: A Critical ReviewAdvanced Energy Materials, 2017
- Thermoelectric properties of a doped LaNiO3 perovskite system prepared using a spark-plasma sintering processElectronic Materials Letters, 2013
- Electrochemical hydrogen charge and discharge properties of La0.1Sr0.9Co1−Fe O3− (y= 0, 0.2, 1) electrodes in alkaline electrolyte solutionElectrochimica Acta, 2013
- Preparation and catalytic activities of the novel double perovskite-type oxide La2CuNiO6 for methane combustionCatalysis Communications, 2012
- Electrochemical properties and hydrogen storage mechanism of perovskite-type oxide LaFeO3 as a negative electrode for Ni/MH batteriesElectrochimica Acta, 2010