One-pot synthesis of confined structure Ru3Sn7 alloy on alumina for an exceptionally rapid and selective hydrogenolysis furfuryl alcohol to 1,5-pentanediol
Authors:
- Rodiansono RodiansonoRRRodiansono Rodiansono
- Atina Sabila AzzahraAAAtina Sabila Azzahra
- Indri Badria AdilinaIAIndri Badria Adilina
- 24 July 2025
- journal article
- research article
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 15 (18) , 5452-5463
Abstract
A facile and one-pot synthesis for confined structure Ru3Sn7 alloy catalysts on Al2O3 for highly efficient and selective synthesis of 1,5-pentanediol (1,5-PeD) from furfuryl alcohol (FFalc) has been developed. Three types of Ru-Sn alloy catalysts were synthesised via three approaches; (i) a one-pot (op) method from ruthenium and tin salt solutions and Al(OH)3 hydrargillite-type at 150 oC for 24 h; (ii) coprecipitation-hydrothermal (cop) procedure and (iii) wet-impregnation (imp) ruthenium and tin salt solutions and Al2O3-500, followed by reduction with H2 at 400 oC for 2 h, and produced (op)Ru-(x)Sn@Al2O3, (cop)Ru-(1.30)@Al2O3-500, and (imp)Ru-(1.23)Sn@Al2O3-500 catalysts, respectively. This obviously allowed the highest yield of 1,5-PeD (97%) with the highest productivity of 1,5-PeD (3.67 mmol 1,5-PeD/gcat. min) from FFalc in water at 140 oC, 10 bar H2, and 3 h. In this kind of (op)Ru-(1.30)Sn@Al2O3 catalysts, the presence of Ru3Sn7 or Ru-SnOx can catalyse the partial hydrogenation of the furan ring of FFalc to form 4,5-dihydrofuranmethanol (4,5-DHFM) and acidic species of SnOx or Snn+ or acidic Al2O3 could serve for activating the C2-O for ring opening processes, while Ru0 works for the following hydrogenation, led to high yield of the final product 1,5-PeD. This is recorded as the first and the highest 1,5-PeD yield compared to the state-of-the-art catalysts in the hydrogenolysis of FFalc to diols under mild reaction conditions. Though catalytic performance of the recycled (op)Ru-(1.30)Sn@Al2O3 catalyst can be restored after the reactivation with H2 at 400 oC for 1 h, the low amount of recyclability of the catalyst remains as the main drawback. Therefore, systematic investigations to overcome the low recyclability of catalyst after repeated reactions are substantially necessary.Keywords
Funding Information
- Direktorat Riset Dan Pengabdian Kepada Masyarakat (056/E5/PG.02.00.PL/2024)
- Lembaga Pengelola Dana Pendidikan (79/IV/KS/11/2022)
- Universitas Lambung Mangkurat (1374.95/UN8.2/PG/2024)
This publication has 51 references indexed in Scilit:
- Recent progress on catalyst development for ring-opening C-O hydrogenolysis of cyclic ethers in the production of biomass-derived chemicalsCarbon Neutrality, 2024
- Effect of potassium in copper catalysts on selective C–O bond activation of furfuryl alcoholApplied Catalysis A: General, 2024
- Review on Metal–Acid Tandem Catalysis for Hydrogenative Rearrangement of Furfurals to C5 Cyclic CompoundsTransactions of Tianjin University, 2023
- Selective Conversion of Cellulose to Hydroxyacetone and 1‐Hydroxy‐2‐Butanone with Sn–Ni Bimetallic CatalystsChemSusChem, 2019
- Chemicals from Biomass: Combining Ring‐Opening Tautomerization and Hydrogenation Reactions to Produce 1,5‐Pentanediol from FurfuralChemSusChem, 2017
- Insights into the Ring‐Opening of Biomass‐Derived Furanics over Carbon‐Supported RutheniumChemSusChem, 2016
- Resolving ruthenium: XPS studies of common ruthenium materialsSurface and Interface Analysis, 2015
- Comprehensive IR study on acid/base properties of metal oxidesApplied Catalysis A: General, 2012
- Behavior of H2 chemisorption on Ru/TiO2 surface and its application in evaluation of Ru particle sizes compared with TEM and XRD analysesApplied Catalysis A: General, 2008
- FT-IR Assessment Through Pyridine Adsorption of the Surface Acidity of Alkali-Doped MoO3/TiO2Journal of Catalysis, 1994