Structural response of Y-Al-O nanoparticles in various environments to swift heavy ion irradiation
Authors:
- Tiep Nguyen VanTVTiep Nguyen Van
- A. SohatskyASA. Sohatsky
- Kateryna KornieievaKKKateryna Kornieieva
- A.D. IbrayevaAIA.D. Ibrayeva
- V.A. SkuratovVSV.A. Skuratov
- Alisher MutaliAMAlisher Mutali
- Nikita KirilkinNKNikita Kirilkin
- Jacques O’COnnellJOJacques O’COnnell
- Bao Trung TranBTBao Trung Tran
- D. D. PhuongDPD. D. Phuong
Preprint
- 21 July 2026
- preprint
- Published by Elsevier in SSRN Electronic Journal
Abstract
The radiation stability of dispersed oxide nanoparticles introduced into ferritic-martensitic alloys for high-temperature strengthening has attracted considerable attention in recent years due to the potential impact of radiation-induced structural changes in the reinforcing particles on the mechanical performance of the material under irradiation. Of particular interest is the amorphization of complex oxide dispersoids exposed to swift heavy particles with energies comparable to those of uranium fission fragments. In the present study, transmission electron microscopy (TEM) was used to investigate the formation of amorphous ion tracks produced by 230 MeV Xe ions in Y4Al2O9 (YAM) nanoparticles, both as free-standing particles and when dispersed within the matrices of well-known oxide-dispersion-strengthened (ODS) alloys, namely PM2000, MA956, and KP4. The results demonstrate that both the morphology and the size of amorphous ion tracks in YAM particles are strongly influenced by the presence of the surrounding ferritic matrix. Specifically, (i) free-standing YAM nanoparticles exhibit the largest track radii, which are independent of particle size and show a relatively narrow and uniform distribution; (ii) in larger YAM particles embedded in ferritic matrices (PM2000 and MA956), the track radius decreases progressively as the oxide-matrix interface is approached; and (iii) no amorphous tracks are observed in the small YAM nanoparticles present in the KP4 alloy. The critical YAM particle size required for amorphous track formation in ferrite is estimated to be approximately 15 nm. The role of the ferritic matrix as a heat sink and the influence of the oxide-ferrite interfacial structure on the efficiency of heat dissipation from ion tracks are discussed. These factors are believed to contribute to the suppression of irradiation-induced disruption of the crystalline structure of the oxide particles.Keywords
This publication has 16 references indexed in Scilit:
- Stability of Y‐Ti‐O nanoparticles in ODS alloys during heat treatment and high temperature swift heavy ion irradiationphysica status solidi (c), 2016
- Swift heavy ion tracks in Y2Ti2O7 nanoparticles in EP450 ODS steelJournal of Nuclear Materials, 2015
- Radiation stability of the ODS alloys against swift heavy ion impactJournal of Nuclear Materials, 2013
- R&D of ferritic–martensitic steel EP450 ODS for fuel pin claddings of prospective fast reactorsJournal of Nuclear Materials, 2012
- Amorphization of oxides in ODS steels/materials by electronic stopping powerJournal of Nuclear Materials, 2012
- Development of Al added high-Cr ODS steels for fuel cladding of next generation nuclear systemsJournal of Nuclear Materials, 2011
- Stability of nano-oxides upon heavy ion irradiation of an ODS materialJournal of Nuclear Materials, 2011
- Amorphization of oxides in ODS materials under low and high energy ion irradiationsJournal of Nuclear Materials, 2011
- HRTEM study of oxide nanoparticles in K3-ODS ferritic steel developed for radiation toleranceJournal of Nuclear Materials, 2011
- Present development status of EUROFER and ODS-EUROFER for application in blanket conceptsFusion Engineering and Design, 2005