Evolution of microstructure and crystallographic texture in a novel Zr-4Nb-2Al alloy during hot rotary swaging
Authors:
- Adam StrnadASAdam Strnad
- Jana ŠmilauerováJŠJana Šmilauerová
- Josef StráskýJSJosef Stráský
- Lukas HorakLHLukas Horak
- Jan CapekJCJan Capek
- Alžběta EndrychováAEAlžběta Endrychová
- Martin HolčákMHMartin Holčák
- Jiri ZýkaJiri Zýka
- Miloš JanečekMJMiloš Janeček
- Petr HarcubaPHPetr Harcuba
Preprint
- 16 October 2026
- preprint
- Published by Elsevier in SSRN Electronic Journal
Abstract
A multi-step induction-assisted hot rotary swaging route was developed for the novel dual-phase Zr–4Nb–2Al alloy to investigate the evolution of microstructure, crystallographic texture, and mechanical properties during sequential deformation. Phase-transformation temperatures determined by electrical resistivity measurements were used to select processing conditions in the single-phase β field at 880 °C and the α+β field at 780 °C. Induction heating with thermographic temperature control enabled reduction of the initial 12 mm rod to 6.3 mm, corresponding to a total area reduction of 72%. Swaging in the β field refined millimetre-sized prior-β grains to approximately 100 µm, while subsequent cooling produced a fine lamellar α+β microstructure. Further deformation in the α+β field disrupted the lamellar structure, promoted globularisation and recrystallisation of the α phase, and refined the β phase. The microstructural evolution was accompanied by a pronounced ⟨112̅0⟩α ∥ SD fibre texture in the α phase, whereas the β phase exhibited predominantly ⟨110⟩β ∥ SD together with a ⟨111⟩β ∥ SD component. The phase constitution remained comparatively stable, with approximately 12–15 wt.% retained β throughout processing. Subsequent α+β swaging decreased the compressive yield strength from 1103 to 839 MPa while increasing plastic deformability, with a maximum fracture strain of 32%. Radial hardness heterogeneity was progressively eliminated. These results demonstrate that induction-assisted rotary swaging in selected phase fields provides an effective route for tailoring microstructure, texture, and mechanical response in dual-phase zirconium alloys with potential nuclear applications.Keywords
This publication has 61 references indexed in Scilit:
- Effect of Temperature on the Structure and Mechanical Properties of Zr–2.5% Nb Alloy Processed by Rotary ForgingTransactions of the Indian Institute of Metals, 2024
- An Overview of the Thermomechanical Processing of α/β Titanium Alloys: Current Status and Future Research OpportunitiesMetallurgical and Materials Transactions A, 2020
- Microstructural Analysis of Orientation-Dependent Recovery and Recrystallization in a Modified 9Cr-1Mo Steel Deformed by Compression at a High Strain RateMetallurgical and Materials Transactions A, 2016
- Modeling the room temperature deformation of a two-phase zirconium alloyActa Materialia, 2009
- Modification of alpha morphology in Ti-6Al-4V by thermomechanical processingMetallurgical Transactions A, 1986
- Compression of zirconium single crystals parallel to theJournal of Nuclear Materials, 1973
- The continuous cooling transformation behaviour of zirconium-niobium-oxygen alloysJournal of Nuclear Materials, 1971
- Annealing textures in zircaloy tubingJournal of Nuclear Materials, 1970
- The solid solubility of aluminum in α-zirconiumJournal of Nuclear Materials, 1970
- Factors affecting the alpha-beta phase boundaries of zirconium and titanium alloysActa Metallurgica, 1958