Antenna-Integrated and PA-Embedded Glass Substrates for D-Band InP Power Amplifier Modules
- 10 March 2025
- journal article
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 15 (4) , 782-791
Abstract
This paper presents an innovative antenna-in-package solution designed for 140 GHz Indium Phosphide (InP) power amplifier (PA) front-end modules. In this design, the InP PAs are strategically embedded at the center of a glass substrate (AGC EN-A1) sandwiched by low-loss dielectric layers (ABF-GL102) on both sides. This arrangement facilitates ultra-short die-to-package interconnects through 20 μm dielectric vias, achieving a remarkably low simulated loss of 0.2 - 0.3 dB at 140 GHz and an impressive S11/S22 of less than -15 dB across a wide frequency range from 110 GHz to 170 GHz. We conducted a thorough evaluation of various PA designs with 2-stage and 3-stage amplifying circuits embedded within this package. The findings reveal that the embedded InP PAs deliver consistent small signal gains of 11.1 dB for the 2-stage and 15.8 dB for the 3-stage PAs at 140 GHz, comparable to their bare die performance and other existing packaging technologies. A key feature of this design is the integration of a 5 μm thick copper heat spreader on the PA backside, which significantly enhances thermal management. Additionally, the design accommodates the seamless integration of a 1 × 8 microstrip patch antenna array. Directly connected to the PA output, this array achieves maximum broadside gains of 12.9 dB, 25.3 dB, and 29.7 dB for the standalone antenna, and the PA-Antenna modules with 2-stage and 3-stage PAs at 139 GHz, respectively, over a 3-dB bandwidth of 5 GHz (136 - 141 GHz). Moreover, the radiation pattern of the PA-Antenna module has been meticulously characterized, showcasing a 13° 3-dB E-plane beamwidth and 64° 3-dB Hplane beamwidth from the broadside. With its superior electrical and thermal performance, scalability, and cost-effectiveness, this package presents a promising solution for developing D-band beamforming arrays in next-generation communication systems.Keywords
Funding Information
- Semiconductor Research orporation (SRC) and DARPA through JUMP 1.0 (ASCENT and ComSenter) and JUMP 2.0 (CHIMES and CUbiC) Programs
- Industry Consortium at the 3D Systems Packaging Research Center, Georgia Institute of Technology
This publication has 33 references indexed in Scilit:
- A Low Loss Die-Embedded Glass Substrate for 140 GHz InP Power Amplifier Integration2024
- Bottom Side Cooling for Glass Interposer with Chip Embedding using Double-sided Release Process for 6G Wireless Applications2023
- RF Glass Technology Is Going Mainstream: Review and Future ApplicationsIEEE Journal of Microwaves, 2023
- Multi-layer FCCSP organic packaging for D-band millimeter wave applications2022
- Fully Integrated 2D Scalable TX/RX Chipset for D-Band Phased-Array-on-Glass Modules2022
- A 140GHz power amplifier with 20.5dBm output power and 20.8% PAE in 250-nm InP HBT technology2020
- Wireless Communications and Applications Above 100 GHz: Opportunities and Challenges for 6G and BeyondIEEE Access, 2019
- Propagation Measurement System and Approach at 140 GHz-Moving to 6G and Above 100 GHz2018
- A 140 GHz MIMO Transceiver in 45 nm SOI CMOS2018
- “zero-undercut” semi-additive copper patterning - a breakthrough for ultrafine-line RDL lithographic structures and precision RF thinfilm passives2015