Fabrication of an integrated piezo-electric micro-nebulizer for biochemical sample analysis
Authors:
- C T PanCPC T Pan
- 21 February 2007
- journal article
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 17 (3) , 659-669
Abstract
This paper proposes a new micro-nebulizer integrating piezo-electric actuator, micro-nozzle plate, and the cavity of a micro-pump to achieve a high-quality nebulizing effect. With this micro-nebulizer, the size distribution of nebulized droplet particles is finer and more uniform than that of commercial ultrasonic and pneumatic ones. Besides, the system power consumption and volume size are lower and smaller than those of the ultrasonic and pneumatic types. Its whole size is about 18 mm × 32 mm × 35 mm in volume and power consumption is about 1 Watt. The fabrication process of a micro-nozzle plate includes multi-exposure and single develop (MESD), high-hardness nickel-cobalt (Ni-Co) alloy micro-electroplating and high-speed precise microinjection molding. A mold with hardness of Vicker (Hv) 550 is obtained. With such hardness, it endures the high-speed injection molding without deformation. The dimensions of nozzle plates are 4 mm in width, 7 mm in length 8 µm in nozzle-hole diameter and 100 µ mi n total thickness. The lowest thickness around a nozzle hole is 40 µm. The aspect ratio is about 5. When the working frequency of a piezo-electric micro-nebulizer is set at 16 KHz, a nebulizing rate of 1.8 cc min−1 is obtained. The developed piezo-electric micro-nebulizer at 16 KHz frequency oscillation shows an excellent mass median diameter (MMD or D(4)(3)) value of 6.13 µm. This micro-nebulizer is applied to nebulize a test sample of myoglobin into a micro-droplet for the analysis of fused-droplet electrospray ionization (FD-ESI) mass spectrometry. Methyl-alcohol solvents of different consistencies are used to react with myoglobin for FD-ESI mass spectrometry analysis. The result reveals that this developed micro-nebulizer shows a better result of mass spectrometry compared to the commercial ultrasonic and pneumatic ones. This micro-nebulizer is applicable to the FD-ESI mass spectrometry analysis. (Some figures in this article are in colour only in the electronic version)Keywords
This publication has 14 references indexed in Scilit:
- Demountable direct injection high efficiency nebulizer for inductively coupled plasma mass spectrometrySpectrochimica Acta Part B: Atomic Spectroscopy, 2004
- Study of flow and heat transfer characteristics and LIGA fabrication of microspinneretsJournal of Micromechanics and Microengineering, 2003
- Direct fabrication of patterned PbS and CdS on organic sheets at ambient temperature by on-site reaction using inkjet printerSolid State Ionics, 2002
- Importance of Drug Delivery System in Steroid Aerosol Therapy via NebulizerPulmonary Pharmacology & Therapeutics, 2002
- Pattern formation in hot embossing of thin polymer filmsNanotechnology, 2001
- DNA-printing: utilization of a standard inkjet printer for the transfer of nucleic acids to solid supportsJournal of Biochemical and Biophysical Methods, 2000
- A thermal inkjet printhead with a monolithically fabricated nozzle plate and self-aligned ink feed holeJournal of Microelectromechanical Systems, 1999
- Injection molding and related techniques for fabrication of microstructuresMicrosystem Technologies, 1997
- Behaviour of the thermospray nebulizer as a system for the introduction of organic solutions in flame atomic absorption spectrometrySpectrochimica Acta Part B: Atomic Spectroscopy, 1996
- The LIGA technique and its potential for microsystems-a surveyIEEE Transactions on Industrial Electronics, 1995