PROVIDING ENHANCED TACTICAL AND TECHNICAL CHARACTERISTICS OF LIGHTLY ARMORED VEHICLES BASED ON DETERMINING THE DYNAMIC STRENGTH OF ARMORED HOUSINGS MADE OF HOMOGENEOUS AND COMPOSITE MATERIALS
Authors:
- Andrey GrabovskiyAGAndrey Grabovskiy
- Mykola M. TkachukMTMykola M. Tkachuk
- Anton VasilievAVAnton Vasiliev
- Mykola A. TkachukMTMykola A. Tkachuk
- Oleh LoznyiOLOleh Loznyi
- Volodymyr TrotsenkoVTVolodymyr Trotsenko
- Vadim SoloveiVSVadim Solovei
- Andrii BohachABAndrii Bohach
- Oleh RikunovOROleh Rikunov
- Serhii MalakeiSMSerhii Malakei
Open Access
- 27 October 2025
- journal article
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
- No. 1,p. 27-46
Abstract
The paper describes an approach to express analysis of the dynamic stress-strain state of armored hulls of light armored vehicles made of composite materials. To do this, the stress-strain state, natural frequencies of oscillations and natural forms of oscillations of test “sandwich armored panels” are determined. The outer layers of these panels are made of steel, and the inner layer is made of ceramics, plastic or rubber. After analyzing the stress-strain state, natural frequencies and natural forms of oscillations of these test panels, some “equivalent” homogeneous armored panel is determined. In the future, the properties of this equivalent panel are incorporated into the calculation model of the dynamic stress-strain state of the studied armored hull of a light armored vehicle. Such an express model allows for an operational analysis of the dynamic, strength and stiffness characteristics of armored hulls of light armored vehicles at the initial stages of design research. This approach can also be used to analyze the protection of armored hulls from the effects of kinetic, high-explosive, cumulative and other types of ammunition. At the final stages of design research, the developed models require further improvement. During preliminary studies, certain patterns and trends are identified. These findings enable the establishment of measures to enhance the strength and dynamic properties of the armored hulls of light armored vehicles. Additionally, it is possible to reduce disturbances in the weapon stabilization and guidance systems installed in combat modules, which are based on the armored hulls of combat vehicles. A comprehensive approach has been developed to improve the tactical and technical characteristics of strength, protection, and firing accuracy by using composite materials for the manufacture of armored hulls of light armored vehicles.Keywords
This publication has 17 references indexed in Scilit:
- One-Dimensional vs. Three-Dimensional Models in Free Vibration Analysis of Axially Functionally Graded Beams with Non-Uniform Cross-SectionsMechanics of Composite Materials, 2024
- Analysis of Natural Frequencies in Non-uniform Cross-section Functionally Graded Porous BeamsJournal of Vibration Engineering & Technologies, 2024
- Higher-order model with interlaminar stress continuity for multi-directional FG-GRC porous multilayer panels resting on elastic foundationEngineering Structures, 2023
- Three-dimensional natural frequency investigation of bidirectional FG truncated thick hollow coneEngineering Computations, 2022
- Influence of the Structure of Hydrophobic Porous Silica Materials of SBA-15 Type and Polymethylsiloxane Derivatives on the Value of Water Intrusion PressureTheoretical and Experimental Chemistry, 2021
- Efficient free vibration analysis of FGM sandwich flat panels with conventional shell elementsMechanics of Advanced Materials and Structures, 2021
- Strength Assessment of Welded Joints of High-Strength Alloy Steels by Indentation MethodStrength of Materials, 2020
- Review of current trends in research and applications of sandwich structuresComposites Part B: Engineering, 2018
- Analysis of behind the armor ballistic traumaJournal of the Mechanical Behavior of Biomedical Materials, 2015
- The influence of material type on the response of plates to air-blast loadingInternational Journal of Impact Engineering, 2015