Macro‐structural effect of metal surfaces treated using computer‐assisted yttrium‐aluminum‐garnet laser scanning on bone–implant fixation
Authors:
- 9 March 2005
- journal article
- research article
- Published by Wiley in Journal of Biomedical Materials Research Part A
- Vol. 73A (2) , 213-222
Abstract
Porous coatings have been applied to the surface of prosthetic devices to foster stable device fixation. The coating serves as a source of mechanical interlocking and may stimulate healthy bone growth through osseointegrated load transfer in cementless arthroplasty. Joint arthroplasty by porous‐coated prostheses is one of the most common surgical treatments, and has provided painless and successful joint mobility. However, long‐term success is often impaired by the loss of fixation between the prosthesis and bone. Porous‐coated prostheses are associated with several disadvantages, including metal debris from porous coatings (third body wear particles) and irregular micro‐texture of metal surfaces. Consequently, quantitative histological analysis has been very difficult. These issues arise because the porous coating treatment is based on addition of material and is not precisely controllable. We recently developed a precisely controllable porous texture technique based on material removal by yttrium‐aluminum‐garnet laser. Free shapes can be applied to complex, three‐dimensional hard metal surfaces using this technique. In this study, tartan check shapes made by crossing grooves and dot shapes made by forming holes were produced on titanium (Ti6A14V) or cobalt chrome (CoCr) and evaluated with computer‐assisted histological analysis and measurement of bone–metal interface shear strength. Width of grooves or holes ranged from 100 to 800 μm (100, 200, 500, and 800 μm), with a depth of 500 μm. When the cylindrical porous‐texture‐treated metal samples (diameter, 5 mm; height, 15 mm) were implanted into a rabbit femoral condyle, bone tissue with bone trabeculae formed in the grooves and holes after 2 or 4 weeks, especially in 500‐μm‐wide grooves. Abundant osteoconduction was consistently observed throughout 500‐μm‐wide grooves in both Ti6A14V and CoCr. Speed of osteoconduction was faster in Ti6A14V than in CoCr, especially in the tartan check shape made of 500‐μm‐wide grooves. In pushout testing, the tartan check shape made of 500‐μm‐wide grooves had significantly higher bone–metal interface shear strength than the dot shape or commercial porous coating. These results indicate that the tartan check shape made of 500‐μm‐wide grooves on metal surfaces has potential for clinical application in artificial prosthesis design. © 2005 Wiley Periodicals, Inc. J Biomed Mater Res 73A: 213–222, 2005Keywords
This publication has 25 references indexed in Scilit:
- Microrough implant surface topographies increase osteogenesis by reducing osteoclast formation and activityJournal of Biomedical Materials Research Part A, 2004
- COMPARISON OF POROUS-COATED TITANIUM FEMORAL STEMS WITH AND WITHOUT HYDROXYAPATITE COATINGJournal of Bone and Joint Surgery, 2003
- The outcome of cemented vs. cementless fixation of a femoral component in total knee replacement (TKR) with the identification of radiological signs for the prediction of failureThe Knee, 2000
- Integral porous femoral stemThe Journal of Arthroplasty, 1997
- Clinical and radiographic outcome of a cementless, titanium, plasma spray-coated total hip arthroplasty femoral componentThe Journal of Arthroplasty, 1996
- A light and electron microscopic study of the effects of surface topography on the behavior of cells attached to titanium‐coated percutaneous implantsJournal of Biomedical Materials Research, 1991
- The wear behavior of ion‐implanted Ti‐6Al‐4V against UHMW polyethyleneJournal of Biomedical Materials Research, 1990
- Tailored Surface Modification by Ion Implantation and Laser TreatmentScience, 1984
- Friction and wear properties of polymer, metal, and ceramic prosthetic joint materials evaluated on a multichannel screening deviceJournal of Biomedical Materials Research, 1981
- Fiber metal composites in the fixation of skeletal prosthesisJournal of Biomedical Materials Research, 1973